User manual FUJITSU A3110

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FUJITSU A3110. We hope that this FUJITSU A3110 user guide will be useful to you.


FUJITSU A3110 : Download the complete user guide (3240 Ko)

You may also download the following manuals related to this product:

   FUJITSU A3110 Document (161 ko)
   FUJITSU A3110 Software Guide (237 ko)

Manual abstract: user guide FUJITSU A3110

Detailed instructions for use are in the User's Guide.

[. . . ] falcon. book Page 1 Friday, August 4, 2006 11:12 AM Fujitsu LifeBook A3110 Notebook ® User's Guide falcon. book Page 2 Friday, August 4, 2006 11:12 AM falcon. book Page 3 Friday, August 4, 2006 11:12 AM Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. MS, MS-DOS, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The ExpressCard word mark and logo are owned by the Personal Computer Memory Card International Association (PCMCIA) and any use of such marks by Fujitsu Computer Systems Corporation is under license. [. . . ] *System CMOS checksum bad ­ run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. *System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. Contact your support representative for repairs. 56 nnnn System RAM Passed Where nnnn is the amount of system memory in kilobytes successfully tested. UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. EMERGENCY MEDIA PLAYER DRIVE TRAY RELEASE If for some reason the eject button fails, you can open the DVD/CD-ROM tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. The tray will pop out a short distance. MODEM RESULT CODES The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are: OK NO CARRIER NO DIALTONE CONNECT 53000 (Connection complete at 53, 000 bps. ) ERROR FAX RING (This means an incoming call. ) BUSY NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation. falcon. book Page 57 Friday, August 4, 2006 11:12 AM Troubleshooting RESTORING YOUR PRE-INSTALLED SOFTWARE The Drivers and Applications Restore (DAR) disc contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below. In order to install applications and/or drivers from the DAR disc, you will need to use an optical drive either in your system or attached externally. 5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. RESTORING THE FACTORY IMAGE The Restore Disc that came with your system contains two utilities: If you have access to the internet, visit the Fujitsu website at: http://www. us. fujitsu. com/computers to check for the most current information, drivers and hints on how to perform recovery and system updates. The Recovery utility allows you to restore the original contents of the C: drive. The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions. · The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Web shopping site at: www. shopfujitsu. com · This disc can only be used with the system with which it was purchased. Reinstalling Individual Drivers and Applications The DAR disc can be used to selectively reinstall drivers and/or applications that may have been uninstalled or corrupted. There may be certain free third-party applications pre-installed on your system that are not on the DAR disc. The latest versions of the applications can be downloaded from the third-party's website. To reinstall drivers and/or applications: 1. A window will appear containing a list of applications, drivers, and utilities that you can install from the DAR disc. The components listed are color-coded in terms of their install status. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed. BOOT Priority Change Before restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/ change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: 1. Start your system and press the [F2] key when the Fujitsu logo appears. If "Optical Media Drive" or "CD-ROM Drive" is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. [. . . ] Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank passwords to console login only. Dialog appears after OmniPass authentication during Windows Logon After installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FUJITSU A3110




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FUJITSU A3110 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.