User manual EPSON EMP-30

[. . . ] 6 Getting Started Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setup Special Notes on Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Setup Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] [Guide for explanation of symbols] : Tilt the Enter button up or down. : Press the Esc button. [Opening and Closing Menus] Press the Menu button to display the top menu. [Menu Selection] Tilt the Enter button up. Tilt the Enter button up or down to move the pointer up or down. Tilt the Enter button down. [Moving in Hierarchy Structure Sub-menu selection] Press the Enter button to move to the sub-menus. When pressing the Esc button, the settings will be saved and the menu returns to the top menu. Press the Menu button to clear the menu display. Press Enter Press Esc 42 Video Menu Displaying Menus Press the Menu button, use the Enter button to select "Video" from the top menu displayed, and press the Enter button to move to a submenu. Tip: · When there is no video signal from a Computer / Component Video device, the "Video" menu is not available for settings. · When there is no video signal from a Video device, only the "Mode" menu is available for settings. Settings Video menu elements to be set differ as follows when projecting computer/ component video versus video images. Computer/Component Video Projection Video Projection D-Sub15: Computer/Component video Video: Video image Menu Position Content Adjust video position vertically and horizontally. * After position is adjusted, changes in the video signal from a computer (such as changes in output mode or display color) may change the adjusted value. Adjust when flickering or blurring occurs (available for setting only when input signal is RGB). * When tracking is wrong, adjustment of sync will not correct flickering. : setting available : setting not available Video Projection D-Sub15 Video Tracking* Sync. * 43 Menu Brightness Contrast* Color Tint Sharpness Gamma* Input Signal Auto Setup Mode Aspect Ratio Reset D-Sub15: Computer/Component video Video: Video image Video Projection Content D-Sub15 Video Adjusts image brightness. * If keystone correction makes unevenness distinctive, reduce the sharpness. After sleep mode is activated, the projector enters standby mode when no signal is input from an external source for a continuous period of 30 minutes. ON : Sleep Mode active OFF : Sleep Mode inactive Returns Setting menu settings to their factory shipping values. To reset all menus to factory shipping values, use the Reset All menu. Sleep Mode Reset 48 Advanced Menu Displaying Menus Press the Menu button, use the Enter button to select "Advanced" from the top menu displayed, and press the Enter button to move to a submenu. Settings Menu Language Content Select the menu language. Select from Japanese, English, German, French, Italian, Spanish, Portuguese, Chinese and Korean. Use color temperature or RGB to create settings for the colors displayed on screen. Select "Color Temp" and press the Enter button to create settings. This setting is used for projection with the projector hanging from a ceiling. To reset all menus to factory shipping values, use the Reset All menu. Color Setting Rear Proj. Ceiling Reset 49 About Menu Displaying Menus Press the Menu button, use the Enter button to select "About" from the top menu displayed, and press the Enter button to move to a submenu. Setting and Display Information The settings information displayed in the About menu differs as shown below during video projection from a computer/component versus a video device. Computer/Component Video Projection Video Projection D-Sub15: Computer/Component video Video: Video image Menu Lamp Reset Lamp Timer Video Source Input Signal Frequency Content Displays cumulative lamp-on time. (When set to Auto in the menu, "Auto (NTSC)" is displayed. ) : Display : No display Video Projection D-Sub15 Video SYNC Polarity SYNC Mode Resolution Refresh Rate Video Signal 50 Reset All Menu Displaying Menus Press the Menu button, and use the Enter button to select "Reset All" from the top-level menu displayed. Settings Menu Reset All Content Returns all menu settings to initial settings. (Lamp and language settings excluded) * Note that rear and invert settings will also be cleared by this operation. 51 Initial Settings List Initial settings at product shipment are shown below. Main Menu Title Video (Computer/ Component Video) Submenu Title Position Tracking Sync. Brightness Contrast Sharpness Gamma Input Signal Auto Setup Aspect Ratio Position Brightness Contrast Color Tint Sharpness Gamma Mode Aspect Ratio Volume Tone Audio Input Cursor/Stamp Initial Settings Central value Dependent on the connected signal 0 Central value Normal RGB ON 4:3 Video (Video) Central value Normal Auto 4:3 Central value Auto Shape: Zoom Rate: 100% Width: 2 M Central value Blue ON Black OFF Audio Effect Setting Advanced Horizontal Bar Cursor Speed Keystone No-Signal Msg Prompt A/V Mute Sleep Mode Language Color Setting Rear Proj. [. . . ] This signal consists of three components, the luminance (Y), red minus luminance (U) and blue minus luminance (V). The human eye is more sensitive for changes in brightness than changes in color. By using this feature, the data volume assigned to the brightness is larger. To prevent a deterioration of the image quality, a high data compression rate is used. [. . . ]