User manual EINHELL SB 401-1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EINHELL SB 401-1. We hope that this EINHELL SB 401-1 user guide will be useful to you.


EINHELL SB 401-1 : Download the complete user guide (1532 Ko)

Manual abstract: user guide EINHELL SB 401-1

Detailed instructions for use are in the User's Guide.

[. . . ] follow the maintenance regulations and the instructions for changing tools. Wear suitable work clothes and personal protection equipment Loose clothing is not suitable, as it can be caught by moving parts, causing you to become entangled. As a general rule, jewelry should not be worn when working with machine tools. Keep your work area neat and tidy Disorder in the work area can easily lead to accidents. [. . . ] B Fasten the mounting flange with pillar (2) to machine base (1) using three screws (3) and washers. B Push the drill table (4) with drill table clamp shaft onto the pillar (2) (Fig. B Lock the drill table into the desired position using the clamping screw (5). B Place the drill head (6) with V-belt cover (7) and motor (8) onto the drill pillar and fasten using the grub screw (20). B Screw the three ball-shaped handles (9) onto the feeder cross handle. Note: All bare parts are greased in order to protect them from corrosion. Before mounting the drill chuck (10) onto the spindle (11), both parts must be completely degreased using an environmentally friendly solvent. 1/2) Before the drill is started for the first time, it must be solidly and fully mounted on the work area of a stable workbench. Note: The fixing screws may only be tightened to a point where they do not distort or deform the base plate. Push the transparent cover (23) into the groove of the red mounting frame (24) and fasten it again with the recessed head screws (21). The height of the cover (23) is infinitely adjustable and can be locked using the two thumb screws (22). The chip guard (13) can be flipped upwards to change drill bits; ensure, however, that the chip guard (13) is back in its initial position before restarting the machine. Prior to starting Ensure that the voltage of the mains supply complies with the specifications on the rating plate. Connect the machine only to a socket with the properly installed earthing contact. 14 The table drill is equipped with a no-volt trip that is designed to protect the operator from an undesired restart following a drop in voltage. 3) To switch on the machine, push in the green On button , , I" (18); the machine starts up. to switch off , press the red Off button , , O" (19); the device shuts down. If the sound of the motor drops in pitch during operation, it is being overloaded. Do not overload the device to the point where the motor comes to a standstill. The machine is designed for continuous operation with intermittent load (S2 15 min. The machine may be operated under a full load for a maximum of 15 minutes, at which time the machine needs to idle for 15 minutes. 1/2) Make sure that the power plug is removed from the socket-outlet before changing tools. [. . . ] properly set the height and angle of the drill table for each workpiece. There must be enough distance between the upper edge of the workpiece and the tip of the drill bit. Drilling wood Please note that sawdust must be properly evacuated when working with wood, as it can pose a health hazard. Ensure that you wear a suitable dust mask when performing work that generates dust. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE EINHELL SB 401-1




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EINHELL SB 401-1 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.