User manual EINHELL E-PST 710-LASER
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EINHELL E-PST 710-LASER. We hope that this EINHELL E-PST 710-LASER user guide will be useful to you.
Manual abstract: user guide EINHELL E-PST 710-LASER
Detailed instructions for use are in the User's Guide.
[. . . ] Bitte vor Montage und Inbetriebnahme die Betriebsanleitung aufmerksam lesen Please read the operating instructions carefully before assembling and using Veuillez lire attentivement ce mode d'emploi avant de procéder au montage et à la mise en service Gelieve vóór montage en ingebruikneming de gebruiksaanwijzing aandachtig te lezen S Var god läs bruksanvisningen noggrant före montering och driftstart Si prega, prima di assemblare ed avviare il trapano, di leggere attentamente le istruzioni sul funzionamento Ped montází a uvedením do provozu si prosím pozorn pectte návod k obsluze Pred uvedením do prevádzky si starostlivo precítajte návod na obsluhu a bezpecnostné pokyny a dodrziavajte ich!Switching off: 1 2 3 4 5 6 7 8 9 10 11 12 13 Power cable Locking button On/Off switch Knurled screw for regulating the speed Inspection guard Saw blade Guide roller Adjustable base Selector switch for pendulum action Adapter for chip extractor Allen key Parallel stop On/Off switsch Laser sed and lock with the locking button Press the On/Off switch and release Electronic speed control setting (Figure 3) Using the knurled screw on the On/Off switch you can pre-set any speed. [. . . ] never direct the laser beam at reflecting surfaces or persons or animals. Caution: It is vital to follow the work procedures described in these instructions. Using the tool in any other way may result in hazardous exposure to laser radiation. When the device is not going to be used for an extended period of time, the batteries should be removed. Adjusting the base (Figure 4) For miter cuts and angular cuts you can swivel the soleplate by up to 45° to either side after undoing the screw at the rear. To adjust the cutting angle, undo the two screws (Figure 4) until you can just about move the blade. Any vacuum cleaner can be connected to the socket at the rear of the jigsaw. If you require a special adapter, please contact the manufacturer of your vacuum cleaner. Nominal voltage: Power consumption: Cutting rate: Stroke height: Cutting depth in wood: Cutting depth in plastic: Cutting depth in iron: Mitre cuts: Sound pressure level LPA: Sound power level LWA: Vibration aw Double isolation Weight Laser class Laser wave length Laser output Laser module power supply 230 V ~ 50 Hz 710 W 0-2800 strokes/min. Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required Replacement part Replacement part number Carbon brush Switch 44. Switching on: Press the On/Off switch Continuous operation: Lock the On/Off switch with the locking button Switching off: Press the On/Off switch and release Turn the speed controller to increase the cutting rate The soleplate can be adjusted through 45° by loosening the screw. Operating the laser You can switch the laser ON and OFF with the switch 1. [. . . ] Please note the details for contacting the customer service center responsible for your region or the service address listed below. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EINHELL E-PST 710-LASER
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EINHELL E-PST 710-LASER will begin.