User manual EINHELL BT-TC 600

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EINHELL BT-TC 600. We hope that this EINHELL BT-TC 600 user guide will be useful to you.


EINHELL BT-TC 600 : Download the complete user guide (1141 Ko)

You may also download the following manuals related to this product:

   EINHELL BT-TC 600 (1056 ko)
   EINHELL BT-TC 600 (1056 ko)
   EINHELL BT-TC 600 (1056 ko)
   EINHELL BT-TC 600 DATASHEET (2251 ko)
   EINHELL BT-TC 600 ANNEXE 108 (1056 ko)
   EINHELL BT-TC 600 ANNEXE 114 (1056 ko)
   EINHELL BT-TC 600 ANNEXE 169 (1056 ko)
   EINHELL BT-TC 600 DATASHEET (1747 ko)

Manual abstract: user guide EINHELL BT-TC 600

Detailed instructions for use are in the User's Guide.

[. . . ] Please read the operating instructions carefully and observe the information provided. It is important to consult these instructions in order to acquaint yourself with the equipment, its proper use and safety regulations. For safety reasons, the tile cutting machine is not to be used by children, young people under 16 years of age, or any other persons who are not acquainted with these operating instructions. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. [. . . ] Press the reset key (22) again in order to be able to start up the machine. 2) To replace the wheel when worn, proceed as follows: Pull out the power plug first. Unscrew the lock nut (18) on the wheel flange (16) with a 19 mm wrench. Take out the worn diamond cutting wheel (15) and fit the new one to the flange, then fit the outer flange (16) and tighten with the nut (18). 3/6) Insert the splitter (19) through the table and into the holder (11) from above and fasten with the screws (20). Move the wheel guard to approximately 5 mm above the tile you wish to cut. Lock the wheel guard (3) in position with the knurled screw (9) as shown in Fig. Position the tile with the glazed side on the work surface and make sure that the diamond wheel does not touch the glaze on the tile. 5 shows the correct position for your hands during miter cutting to 45°. The right hand holds the workpiece in contact with the diamond wheel while the left hand pushes the workpiece forward. the rate of advance must not exceed the cutting capacity of the wheel. This is to make sure that no material comes off, as this may cause accidents or injuries. Always pull out the mains power plug before starting any cleaning work. 1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. 2 Maintenance There are no parts inside the equipment which require additional maintenance. 3 Ordering replacement parts Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www. 1/4) Set the cutting width with the parallel stop (2) and lock in position with the thumb screws (10). the rate of advance must not exceed the cutting capacity of the wheel. This is to make sure that no material comes off, as this may cause accidents or injuries. [. . . ] The following are also excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the operating instructions (e. Connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies into the device (e. Damage caused by the device being dropped) and normal wear resulting from proper operation of the device. The guarantee is rendered null and void if any attempt is made to tamper with the device. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE EINHELL BT-TC 600




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EINHELL BT-TC 600 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.