User manual EINHELL BT-SH 90-350
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EINHELL BT-SH 90-350. We hope that this EINHELL BT-SH 90-350 user guide will be useful to you.
You may also download the following manuals related to this product:
EINHELL BT-SH 90-350 DATASHEET (126 ko)
EINHELL BT-SH 90-350 ANNEXE 753 (911 ko)
EINHELL BT-SH 90-350 DATASHEET (99 ko)
Manual abstract: user guide EINHELL BT-SH 90-350
Detailed instructions for use are in the User's Guide.
[. . . ] The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. Even when the equipment is used as prescribed it is still impossible to eliminate certain residual risk factors. [. . . ] For this purpose undo the two nuts (H), tilt the motor (5) until the required angle is shown on the scale (13) and secure it by tightening the two nuts (H) (Fig. 3 Grinding set saw blades To grind saw blades with set teeth, the motor (5) must be titled to the set angle of the saw blade as described in point 6. 2 but in this case every second tooth must be ground according to its set. Then adjust the angle to the set of the teeth you have not yet ground (see point 6. If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its aftersales service or similarly trained personnel to avoid danger. Always pull out the mains power plug before starting any cleaning work. 1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Undo the three screws (M) on the grinding wheel cover (8) and remove it (Fig. Place the pin (C) in the opening (I) and slowly turn the grinding wheel (10) by hand until the pin (C) blocks the equipment's drive shaft (Fig. Clean the flange and fit the new grinding wheel using the above instructions in reverse and secure it. 2 Grinding saw blades Proceed as follows to grind saw blades: Switch on the equipment (see 7. 1) Turn the saw blade so that the grinding wheel (10) is between the saw blade teeth and then move the grinding wheel (10) as far as possible to the front using the handle (7) (Fig. Turn the saw blade slowly and carefully in a clockwise direction into the rotating grinding wheel (10) and grind the carbide metal plates on the saw blade until their cutting edge has been sharpened (Fig. When the grinding wheel is at 12 o'clock, your hands must be at 3 o'clock and 9 o'clock on the saw blade. Turn the saw blade back anti-clockwise so that the grinding wheel (10) can run freely between the saw blade teeth. Turn the saw blade one tooth further and repeat the process until you have sharpened all the teeth. 2 Adjusting the tilt angle Check the tilt angle of the motor (5) before using the equipment for the first time and at regular angles thereafter. To do this, place a stop angle between the base plate (1) and the motor holder (6) and check whether the pointers (B) on the scales (13) display 0° (Fig. If this is not the case, undo the retaining nuts on the pointers (B) and adjust them. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EINHELL BT-SH 90-350
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EINHELL BT-SH 90-350 will begin.