User manual EINHELL BG-PM 46-1 S

[. . . ] Vor Inbetriebnahme Bedienungsanleitung und Sicherheitshinweise lesen und beachten Read and follow the operating instructions and safety information before using for the first time. Störung Unruhiger Lauf, starkes vibrieren des Gerätes mögliche Ursache - Schrauben lose - Messerbefestigung lose - Messer unwuchtig Motor läuft nicht - Bremshebel nicht gedrückt - Gashebel falsche Stellung - Zündkerze defekt - Kraftstofftank leer - Benzinhahn geschlossen - Vergaser-Benzin abgestanden Motor läuft unruhig - Luftfilter verschmutzt - Zündkerze verschmutzt Rasen wird gelb, Schnitt unregelmäßig - Messer ist unscharf - Schnitthöhe zu gering - Motordrehzahl zu gering Grasauswurf ist unsauber - Motordrehzahl zu gering - Schnitthöhe zu niedrig - Messer abgenutzt - Fangsack verstopft Behebung - Schrauben prüfen - Messerbefestigung prüfen - Messer ersetzen - Bremshebel drücken - Einstellung prüfen - Zündkerze erneuern - Kraftstoff einfüllen - Benzinhahn öffnen - Vergaser-Benzin ablassen (siehe auch Wartung) - Luftfilter reinigen - Zündkerze reinigen - Messer schärfen - richtige Höhe einstellen - Hebel auf max. Safety regulations Layout Intended use Technical data Before starting the equipment Operation Cleaning , maintenance, storage, transport and ordering of spare parts 8. When using the equipment, a few safety precautions must be observed to avoid injuries and damage. [. . . ] Do not make any adjustments or repairs until the engine has been switched off. Pay special attention if you are mowing directly next to a street or are close by one (traffic). Avoid mowing in places where the wheels have trouble gripping or mowing is unsafe in any other way. Before you back up, ensure that nobody is standing behind you (especially little children, who are more difficult to see). When mowing over thick, high grass, select the highest cutting level and mow at a slower speed. Before you remove any grass or blockages of any kind, switch off the engine and pull the plug boot. 4 Emptying the grass basket As soon as grass clippings start to trail the lawn mower, it is time to empty the grass basket. Before taking off the grass basket, switch off the engine and wait until the blade has come to a stop. To take off the grass basket, use one hand to lift up the chute flap and the other to grab onto the basket handle (Fig. For safety reasons, the chute flap automatically falls down after removing the grass basket and closes off the rear chute opening. If any grass remains in the opening, it will be easier to restart the engine if you pull the mower back approx. Do not use your hands or feet to remove clippings in or on the mower housing, but instead use suitable tools such as a brush or a hand broom. In order to ensure that the majority of grass clippings are picked up, the inside of both the catch bag and especially the air grill must be cleaned after each use. Reattach the catch bag only when the engine is switched off and the blade is stopped. Using one hand, lift up the chute flap, while grabbing onto the basket handle with the other. Allow the engine to cool before you put the lawn mower in an enclosed area. Check all the screws and nuts once more before you start to use the lawn mower again. Only original parts or parts approved by the manufacturer may be used for repairs (see address on the warranty certificate). If the lawn mower is not going to be used for an extended period, empty the petrol tank using a petrol suction pump. How to switch off the engine: All you have to do to switch off the engine is release the engine start/stop lever (Fig. Close the petrol cock and pull the spark plug boot from the spark plug boot in order to prevent the engine from restarting. Before you start the engine again, check the cord for the engine brake. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. [. . . ]