User manual DSC ESCORT 558OTC V3.0

[. . . ] ·WARNING· This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Instruction Manual ESCORT558OTC Version 3. O FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart "B" of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If you are certain that the premises are safe, you can silence the alarm by disarming the system. If the alarm was unintentional, notify your central station and/or the local authorities immediately to prevent an unnecessary response. You can determine the cause of an alarm by reviewing the alarm memory (see Section 3. 5-- Alarm Memory). zones secured) and the system disarmed, your system/partition can be re-armed. 6 A R M I N G A N D D I S A R M I N G 3. 5 Your system will record any alarms that occurred while the system/partition was armed. If an alarm occurred while the system/partition was armed, upon disarming it the following message will be announced: "There are (number) alarms in memory: {Zone XX}. " To hear again the zones that went into alarm, press []. The system will prompt: "For Alarm Memory, press [3]. " Press [3], and the system will indicate the zones in Alarm Memory: "There are (number) alarms in memory, {Zone XX}. To exit, press [#]. " When finished reviewing the zones in alarm memory, press [#] to return to the other system status messages. Alarm Memory 3. 6 Bypassing Zones Zones may be bypassed when access is required to part of a protected area while the system/partition is armed. Once a system is armed, bypassed zones will not trigger an alarm when they are breached. To bypass zones, first access the security system (Section 2--Accessing Your Security System) and select a partition (Section 2. 5--If You Have a Multiple Partition System). The system prompts: "For Zone Bypassing, press [1]. " Press [1]. If your system requires that you enter an access code to bypass zones, the system will prompt: "Enter your access code. " Enter your [access code]. The system will announce the Zone Bypass menu: "There are (number) zones bypassed: {Zone XX}, etc. . . To exit, press [#]. " To bypass a zone, enter the one- or two-digit zone number. The system will announce: " There are (number) zones bypassed: {Zone XX}, etc. . To exit, press [#]. " You can now arm the system/partition at any time (see Section 3. 1--Away Arming) and the zone(s) you selected will be bypassed. Zone bypasses are automatically removed each time the system/partition is disarmed and must be reapplied before the next arming. For security reasons, your installer may program your system to prevent the bypass function from affecting certain zones. 7 S E C T I O N Trouble Conditions S E C T I O N 4 7 The control panel continuously monitors a number of possible trouble conditions. If one or more of these conditions occur, the regular keypad will beep twice every ten seconds. To hear the trouble conditions present on your system/partition disarm the system (depending on the control panel you have, your system may allow you to enter the Trouble menu without first disarming the system/partition). Access the security system (Section 2--Accessing Your Security System) and select a partition (Section 2. 5--If You Have a Multiple Partition System). You will hear the prompt: " For System Troubles, press [2]. " Press [2] and the system will announce one or more of the trouble conditions from the list below, if any are present. If no trouble conditions are present, the system will announce: " There are NO System Troubles. [. . . ] Once access is gained to the Escort, a normal system access code is still usually required to access system functions. One of up to 5 modes in which an EMS thermostat can be operating: Off, Heat, Cool, Automatic, Emergency. smoke detector, door/window contact, motion detector, glassbreak detector, etc. ). 19 LIMITED WARRANTY Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. [. . . ]