User manual DEPAEPE HD2000

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DEPAEPE HD2000. We hope that this DEPAEPE HD2000 user guide will be useful to you.


DEPAEPE HD2000 : Download the complete user guide (480 Ko)

Manual abstract: user guide DEPAEPE HD2000

Detailed instructions for use are in the User's Guide.

[. . . ] 29/29 3 1) Repose combiné (Mise correspondant) Handset, on hold position Passage de la vis antivol Concealed screw hole en attente d’un 2) 3) Touches Mémoires Urgence (Uniquement version avec 2 ou 3 mémoires) Memory keys (Models with 2 or 3 memory keys only) Clavier uniquement modèle HD2000 « Urgence à clavier »). 17 Introduction There are 4 different models of HD2 Urgence telephones: -HD2000 Urgence 1: with direct dialling of 1 programmed number when lifting the handset. - HD2000 Urgence 2: direct dialling of 2 programmed numbers when depressing key M1 or M2. [. . . ] NOTE: To erase a number stored in memory, proceed from 1 to 4, skip section 5 (Do not enter any digit) and terminate as in 6 and 7. NOTE: HD2000 Urgence 1 and Urgence à clavier factory settings come with “Urgence“ mode. In case of wrong operation, see « LIST OF SETTINGS » pages 24-25 and check that “Urgence” mode is selected. Setting access code : Setting choice 04 Urgency:1 20 Mode 2 HD2000 Urgence 2 or 3 1) Make sure HD2000 Urgence is connected to the line. 4) Dial the telephone number to store including *, # or "Pause" if needed (22 digits maxi). NOTE: In case of wrong operation, a long "beep" sound is emitted. NOTE: To erase a number stored in memory, proceed from 1 to 3, skip section 4 (Do not enter any digit) press the memory to erase as in 5 and terminate as in 6 and 7. NOTE: HD2000 Urgence2 and 3 factory settings come with “Normal“ mode. In case of wrong operation, see « LIST OF SETTINGS » pages 24-25 and check that “Normal” mode is selected. Setting access code : Setting choice 04 Normal:0 21 Settings programming Note: HD2000 Urgence standard factory settings come with: - Programming access code = 0000 - Dialling = Tone - Hook-Flash duration = 270 ms - Pulse mark-break ratio = 66/33 - Access to memory programming = unlocked - Call barring = unlocked To change settings, proceed as follows: 1) Make sure the telephone is connected to a powered C. 2) Depress « PGR » key located on the small keypad (Located at the back of the unit). 3) While keeping « PGR » key depressed, pick-up the handset. 6) Enter the 4 digits programming access code with the keypad (factory pre set code is: 0000) This code can be modified (see « LIST OF SETTINGS » section, pages 24-25). 7) If the right code is entered, 2 short « beep » tones will be heard and the access to settings, changes will be authorized. If a wrong code is entered, a low « beep » tone will be heard and the unit will return to talk mode. 8) Enter the 2 digits selected setting access code (see « LIST OF SETTINGS » section pages 24-25) 9) 2 sharp « beep » tones confirming the selection will be heard. 22 12) 2 sharp « beep » tones will confirm the storage of your new setting. Total Reset General reset operation erases memories, access code and will return all settings to factory settings (see « SETTINGS PROGRAMMING » section page 22). [. . . ] 4- If needed, install the third screw through the hole located above the telephone (See pages 28 and 29) and hide it with the foam plug. Boucle sèche (Option) Off-hook detection (Optional) Ligne/Line Ligne/Line Boucle sèche (Option) Off-hook detection (Optional) 26 Desk mount installation (Optional) see page 28 Use the optional desk-mount kit including one securing screw, a loaded desk mount base, 2 desk-mount black latches and the 4 non slip pads. 2- Pull of the 2 wall-mount black latches and replace them by 2 smaller desk-mount black latches. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DEPAEPE HD2000




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DEPAEPE HD2000 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.