User manual DEI 250

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DEI 250. We hope that this DEI 250 user guide will be useful to you.


DEI 250 : Download the complete user guide (2059 Ko)

Manual abstract: user guide DEI 250

Detailed instructions for use are in the User's Guide.

[. . . ] The transistorized output can only provide 200 mA of current, and connecting directly to a solenoid, motor, or other high-current device will cause it to fail. H1/4 BLACK/WHITE (-) domelight supervision relay output Connect this wire to the optional domelight supervision relay as shown in the following diagram. 4 © 2001 Directed Electronics, Inc. It cannot be connected directly to the domelight circuit, as the output cannot support the current draw of one or more light bulbs. H1/5 GREEN (-) door trigger input, zone 3 Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground when any door is opened. In vehicles with factory delays on the domelight circuit, there is usually a wire that is unaffected by the delay circuitry. [. . . ] (The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected. ) 2. Key. (The H1/9 YELLOW switched ignition input must be connected. ) 3. Select the receiver channel. Press and release the Valet/Program switch the number of times necessary to access the desired channel. Once you have selected a channel, press and HOLD the Valet/Program switch once more. The siren will chirp and the LED will blink the number of times corresponding to the channel that has been accessed. NOTE: If adding a remote, a button must be taught to Channel One prior to programming other channels. CHANNEL NUMBER 1 2 3 4 5 PRESS AND RELEASE THE VALET/PROGRAM SWITCH One Time Two Times Three Times Four Times Five Times TO PROGRAM FUNCTION Arm/Disarm/Panic Channel 2 Channel 3 Auto Learn Standard Configuration* Delete all transmitters *NOTE: For Auto Learn Standard Configuration, see Transmitter Configuration section of this guide. NOTE: If any transmitter button from a known transmitter is programmed to Channel Five, all transmitters will be erased from memory. This is useful in cases when one of the customer's transmitters is lost or stolen. This will erase any lost or stolen transmitters from the system's memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly. © 2001 Directed Electronics, Inc. While HOLDING the Valet/Program switch, press the transmitter button that you wish to assign to that channel. You cannot teach a transmitter button to the system more than once. NOTE: For Channel 4, press Button I to program the Auto Learn Standard Configuration on a twobutton transmitter. If programming an optional four-button transmitter, then press Button I to assign the standard configuration to Buttons I and II; or press Button III to assign the standard configuration to Buttons III and IV, instead. Once the code is learned, the Valet/Program button can be released. You can advance from one channel to another by releasing the Valet/Program button and tapping it to advance channels and then HOLDING it. For example, if you want to program Channel Three after programming Channel One, release the Valet/Program button. The siren will chirp three times to confirm it is ready to receive the code from the transmitter. Learn Routine will be exited if any of the following occurs: I The ignition is turned off. One long chirp indicates that Learn Routine has been exited. transmitter configuration The transmitters can be programmed with the Standard Configuration by using the Channel 4 Auto Learn Standard Configuration function in the Transmitter/Receiver Learn Routine. When programmed for Standard Configuration, the transmitter buttons are assigned to the following functions: Button I (III*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . operates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Arm/Disarm/Panic Button II (IV*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . operates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Two Buttons I and II (III and IV*) . . . . . . . . . . . . . . . operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Three *NOTE: If using an optional four-button remote, the Standard Configuration may alternately be taught to Buttons III and IV by pressing Button III in Step 4 of the Transmitter/Receiver Learn Routine. 10 © 2001 Directed Electronics, Inc. Vista, CA operating settings learn routine Many of the operating settings of this unit are programmable. They can be changed whenever necessary through the Operating Settings Learn Routine. The Valet/Program push-button switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. Press and release the Valet/Program switch once to advance from Feature 1 to Feature 2. The siren will chirp two times to confirm that you have accessed Feature 2. to exit the learn routine To exit the learn routine, do one of the following: 1. [. . . ] This is an instant trigger, remember, since even if the door is instantly re-closed, the progression from chirps to constant siren will continue. I Closing the door triggers the system, but opening the door does not: Have you correctly identified the type of door switch system?(See H1/5 GREEN Door Trigger Input, Primary Harness Wire Connection Guide section of this guide. ) I System will not passively arm until it is remotely armed and then disarmed: Are the door inputs connected?Is the H1/6 blue wire connected to the door trigger wire in the vehicle? [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DEI 250




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DEI 250 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.