User manual DAITSU DL-26

[. . . ] 10 Viewing the Remote Control - Button Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - Teletext/PIP(Picture in Picture) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - Loading the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Installation Table Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Any extra speaker wire length remaining can be bunched into the wire holders provided. (Caution: Once installed, the speaker wire holders lock into position and can't be removed. ) · Always lift the monitor itself (not the speakers) when handling or moving the monitor after speakers have been installed. Speaker Accessories 4 - Iron Plates (Mount speakers to monitor) 16 - 4 x 10 Long Bolts (Attach iron plates to speakers) 2 - Speaker Wires 2 - Speaker Wire Holders (For arranging the speaker wires) OWNER'S MANUAL 17 Connecting the TV Cable TV Antenna Cable Connecting the TV Cable 1 2 3 4 Connect the TV Antenna cable to the TV input jack. Use PG+/PG- button or numeric button to change TV programme for your programme selection. Press Pre. PG button on the remote control to tune the previous programme. Also, you can tune to cable service provided programmes using the cable box. For further information regarding cable TV service, contact cable TV service provider(s). The Function of SCART 2 Port This signal of SCART 2 port takes first priority over other input signals. When an outer device which is connected to SCART 2 port is "Power On", the monitor will automatically display the signal of SCART 2 port. The display mode (4:3, 16:9) will be automatically recognized until users purposely change the display mode. When users operate up/down button or numeric button on the remote control, input source is changed to TV mode automatically. The SCART 2 recognizes automatically both composite signal and RGB signal. 18 OWNER'S MANUAL Connecting the VCR SCART 2 (Euro connector) SCART 1 (Euro connector) S-Video AV Input Sound of S-Video/AV Connecting the VCR With SCART (Euro cable) Connect a SCART cable to the SCART jacks of the VCR and the monitor. With S-Video Connect a S-Video cable to the S-Video jacks of the VCR and the monitor. Connect L (White), R (Red) sound cable (Composite) to the sound jacks of the VCR and the monitor. With AV Input Connect a composite cable to the AV video jacks of the VCR and the monitor. · 1366 X 768 : 50/63" Native resolution horizontal polarity is positive (+), vertical polarity is negative (-). · Depending on the manufacturer, your PC screen might appear differently (and depending on your particular version of Windows). Check your PC instruction book for information about connecting your PC to a the monitor. · The monitor may operate abnormally if a non-standard video signal. · "Out of range" message box will appear when an over-spec video signal is input. Change the video settings of PC when the message is displayed. OWNER'S MANUAL 23 Basic Operation Turning the Monitor ON/OFF Press the Power button on the remote control. You can also use the Power button on the front panel. Select Source Press INPUT button on the remote control. Then you can see the source list menu shown as below. Source Change 1 TV 2 SCART 1 3 SCART 2 4 S-Video/AV 5 Component 1 6 Component 2 7 PC 8 DVI Select the source to watch with PG+/PG- button on the remote control and press the Menu/Set button. Source list menu TV Programme Selection 1 Connect the signal source (TV antenna) to TV input. Press INPUT button on the remote control and select TV on the source list. Press Pre. PG button on the remote control to watch the previous programme. Also, you can tune the cable service, provided programmes while using the cable box. For further information regarding cable TV service, contact your TV service provider(s). 2 3 4 Volume Control Use VOL+/VOL- button on the remote control to adjust the volume level. [. . . ] Before using the timer, you must set the monitor's Time as described previously. 1 2 Press Menu/Set button to display the main OSD menu. Time Set AM 03:29 AM 05:11 ON 99 100 AM 05:11 OFF OFF Select the Time main menu with PG+/PG- button on the remote control. Move the cursor by VOL+/VOL- button and adjust time by PG+/PG- button. On Time Item Name On Time On Channel 3 4 On Volume Off Time Sleep 5 AM 05:11 ON Auto power-on time Activated 48 OWNER'S MANUAL Setting the Time Setting the On Channel Set the channel when the monitor power turn on automatically. [. . . ]