User manual DAHON MICRO FT LIGHT SCHEMA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DAHON MICRO FT LIGHT. We hope that this DAHON MICRO FT LIGHT user guide will be useful to you.
Manual abstract: user guide DAHON MICRO FT LIGHTSCHEMA
Detailed instructions for use are in the User's Guide.
[. . . ] Obtain and read the service instructions carefully prior to installing the parts. Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, they may come off the bicycle and serious injury may result. [. . . ] If the wheels are loose in any way, they may come off the bicycle and serious injury may result. Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Installation of the CS-S500 sprocket with chain guard
guard to of the 1. Install the chainthen installthe right hand dust cap to the hub body, and right hand dust cap B driver.
cassette joint the direction of 2. Turn the the illustration pulley inthe red marksthe the arrow in to align on
When using the chain tensioner
When using the chain tensioner, be sure to read these service instructions in conjunction with the service instructions for the CT-S500 chain tensioner.
pulley and the bracket. With the cassette joint in this condition, install it so that the red mark on the cassette joint is aligned with the red mark on the right side of the hub body.
Note:
When installing a part such as a mudguard stay to the hub axle, install in the order shown in the illustration below.
Right hand dust cap B Chain guard
Note the direction
Should be aligned
Pulley
Chain tensioner Non-turn washer
CJJA
LOCK
CJ-8S20
8S 20
JAPAN
LOCK
Right hand dust cap
Driver
Cassette joint Hub axle Dropout
CJ-8S20
JAPAN
Mudguard stay Carrier stay Cap nut
Align the red marks to install.
2.
Align the red marks to install.
NOTE:
Place the non-turn washers onto the right side and left side of the hub axle. At this time, turn the cassette joint so that the projecting parts of the non-turn washers fit into the grooves of the dropouts. If this is done, the cassette joint can be installed so that it is almost parallel to the chainstay.
Non-turn washer (for left side)
Note:
When installing the hub to the frame, the chain guard may come off, so check that the chain guard is securely installed so that it will not come off. Different non-turn washers are used at the left and right sides.
Non-turn washer Dropouts Mark /Color Right Left 5L / Brown 7L / Gray 6L / White 5L / Brown 8L / Green 5R / Yellow 7R / Black 6R / Silver 5R / Yellow 8R / Blue Size 20 38 =0 =0 = 60 90
Turn 45°
LOCK
CJ-8S20
JAPAN
Cassette joint fixing ring
Standard Reversed Reversed (full chain case)
SI-35Z0C
SG-S500 CS-S500 CJ-8S20
Hub for Inter-8 Disc Brake Sprocket with Chain Guard Cassette joint
Installation of the cassette joint to the hub
1. Install the driver cap to the driver on the right side of the hub body.
Driver cap
Fit the cassette joint bracket securely.
Vertical
Note the direction
7R
Mark
Installation of the hub to the frame
The method of installing the hub to the frame is the same when the chain tensioner is being used and when it is not being used. Install the non-turn washers so that the projecting parts is securely in the dropouts grooves on either side of the hub axle.
Technical Service Instructions
Driver
1. Mount the chain on the sprocket, and then set the hub axle into the dropouts.
When not using the chain tensioner
Driver cap
7R
3. Take up the slack in the chain and secure the wheel to the frame with the cap nuts.
Tightening torque: 30 45 N·m {260 390 in. lbs. }
7R
20 8S CJ- N
JA PA
Be sure to read these service instructions in conjunction with the service instructions for the brake and the shifting lever before use.
CJN PA JA
Dropout
LOCK
LOCK
Cap nut Hub axle Non-turn washer
CJ-
JA
8S
PA
N
20
ring, align the yellow mark with the yellow mark on the cassette joint pulley, and then turn the cassette joint fixing ring 45° clockwise.
These service instructions explain how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of purchase or the bicycle manufacturer.
These service instructions are printed on recycled paper. [. . . ] lbs. }
7R
20 8S CJ- N
JA PA
Be sure to read these service instructions in conjunction with the service instructions for the brake and the shifting lever before use.
CJN PA JA
Dropout
LOCK
LOCK
Cap nut Hub axle Non-turn washer
CJ-
JA
8S
PA
N
20
ring, align the yellow mark with the yellow mark on the cassette joint pulley, and then turn the cassette joint fixing ring 45° clockwise.
These service instructions explain how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of purchase or the bicycle manufacturer.
These service instructions are printed on recycled paper. Please note: Specifications are subject to change for improvement without notice. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DAHON MICRO FT LIGHT
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DAHON MICRO FT LIGHT will begin.