User manual CLIFFORD AVANTGUARD 2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CLIFFORD AVANTGUARD 2. We hope that this CLIFFORD AVANTGUARD 2 user guide will be useful to you.
Manual abstract: user guide CLIFFORD AVANTGUARD 2
Detailed instructions for use are in the User's Guide.
[. . . ] World-Class Auto Security
TM
AvantGuard
II
Owner's Manual
Table of Contents
EXTREMELY IMPORTANT NOTICE . How to Remotely Control Accessories and/or Other Clifford Systems Valet Mode . 2 2 3 3 4 4 4 5 5 5 5 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 9 10 10 11 11 12 13 13 14 14 15 15 16 17
1
EXTREMELY IMPORTANT NOTICE
If the AvantGuard II's control unit is removed from the vehicle for any reason, the supplied RED jumper wire MUST BE CONNECTED to pins #8 and #11 of the PIGTAIL connector.
WARNING
1. The AvantGuard II is designed to be used only on a gasoline-powered, fuel-injected vehicle with automatic transmission. [. . . ] If need be, this process will automatically repeat every eight hours until the battery is properly charged. Your car is safe and sound since it can't be driven by an intruder even while the engine is running. For the utmost in user-friendliness, you don't have to do a thing to turn off the AutoStart feature. AutoStart is automatically canceled whenever you start the engine with either your remote control or ignition key (or if a fault is detected).
9
How to Engage AutoStart 1. To conserve battery power, make sure the air conditioner, radio and all other accessories are turned off. Insert your ignition key and turn the switch to the "ON" position. Within 10 seconds, press and hold the valet/program switch to its momentary position until you hear 1 chirp, then release the switch. The LED will light in red and stay lit, confirming that the system is now in program mode. The siren will chirp 3 times and the LED will turn off to confirm that the system has exited program mode. Exit and arm the system with remote control button I (channel 1).
· Park the vehicle in an open, well-ventilated area. · Before exiting the vehicle, set the air conditioner, heater, defroster and other
accessories to the desired levels. · Set the air conditioner or heater to the "Recirculate" (rather than "fresh") position. · Make sure the transmission is in "PARK", the hood is closed and the alarm is armed before leaving the vehicle. · When remotely starting, hold button II until the parking lights flash twice. · Before engaging the AutoStart feature, make sure the gas tank is at least half-full and all accessories are off. · For servicing, pull the 5-amp fuse attached to the positive [+] post of the vehicle battery). After servicing is complete, turn on the ignition then reinsert the fuse.
Remote Starter Do's and Don'ts DO
· NEVER allow children to play with the remote control. · NEVER start the engine if the vehicle is parked in a poorly ventilated area. · NEVER remotely start the engine with a person or pet in the car (exhaust fumes
may leak into the passenger compartment).
DON'T
· NEVER remotely start and restart the engine (or turn the ignition on and off)
more than 10 consecutive times without turning the ignition on and placing the transmission in "DRIVE" for at least 3 seconds.
10
How to Program Your AvantGuard II
NOTE: A Quick Programming Guide is on pages 17-19. However, if you are programming the system for the first time, we strongly recommend that you follow the detailed instructions in the specific sections that follow before attempting to use the guide.
or your convenience, everything was preprogrammed for you at the Clifford Electronics factory. If, however, you would like to set your AvantGuard II to meet you own specific needs and preferences, doing so is as simple as a few flicks of a switch.
NOTE: If you wish to program more than one feature at a time, you do not need to exit and re-enter the program mode for each feature separately. Simply leave the ignition on after programming the first feature and continue with STEP 3 of the next feature you wish. [. . . ] With the switch in the center position, press button III on your remote. You will hear 3 chirps to confirm that the new button III code has been added. Otherwise go to step 3 of the next feature you wish to program or turn the ignition off (you will hear 3 chirps and the LED will turn off to confirm the system has exited program mode). How to Program Button IV/Channel 4: The system's channel 4 output may be used to remotely command an optional system accessory (such as a remote trunk release). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CLIFFORD AVANTGUARD 2
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CLIFFORD AVANTGUARD 2 will begin.