User manual CLIFFORD 7500

[. . . ] Always exercise good judgment and common sense when using the remote starter: · NEVER remotely start the engine if parked in an enclosed area lacking sufficient ventilation. · NEVER engage the ShortStop or AutoStart feature if parked in an enclosed area lacking sufficient ventilation. · NEVER remotely start or use ShortStop with a person or pet in the vehicle. · NEVER start with someone behind or in front of the vehicle. Standard Features The following are standard features of this system. [. . . ] The Glass Tampering Sensor rarely ever needs readjustment, but, if needed, can be readjusted by any Authorized Clifford Dealer (preferably your installing dealer). To prevent falsing, system sensors are bypassed when the engine is remotely started. Ask your Authorized Clifford Dealer about this optional sensor that will further enhance the security of your vehicle: n Digital Tilt/Motion Sensor: Detects less than one degree of lifting or any minute motion of the vehicle while completely ignoring all other conditions that falsely set off all other sensors. Even if you park on a hill, the Digital Tilt/Motion Sensor will accurately respond to the first hint of tampering to reliably protect your wheels and entire vehicle. Remote controlled Piezo Sensor zone adjustments If the setting(s) of the sensor zones are either too sensitive or not sensitive enough, you may test and adjust them with the master remote control: 1. On the master remote, press the LevelShift three times, then button 3. To test the primary (alarm) zone, press button 4 (you will hear a 4-chirp confirmation), then firmly "thump" the top of the A-pillar (the area between the side windows near the roof) heel of your fist. If the impact is strong enough to trigger the primary zone, you will hear a siren chirp. To change sensitivity, press button 4 to reduce sensitivity, button 2 to increase sensitivity. Two chirps will acknowledge each sensitivity increase, one chirp will confirm each decrease. You can test the new setting by again thumping the top of the A-pillar. You may now press button 3 to adjust the warning zone (as noted in 3a. below), or press button 1 to fully exit the sensor adjustment mode (you will hear 3 chirps). For the Piezo Sensor warning zone, press button 3 (you'll hear 1 chirp). Then use the same procedure as above, but thump less forcefully for the warning zone. When done, press button 1 to reselect the primary zone (you will hear 2 chirps), then button 1 again to fully exit sensor adjustment mode (you will hear 3 chirps). 7 Smart trunk release option If you have this option, you may use the button to remotely release the trunk latch. The system's electronic interlock prevents unintentional activation of the remote trunk release when you drive, or when the system is armed. The Smart Trunk Release feature requires installer programming, so if you have the optional trunk release installed, you may want to verify that it will NOT activate when the system is armed. If it can be activated while armed, causing the alarm to sound, please return to your installing Clifford Dealer and have them correct this (it only takes a couple minutes and there will be no charge to you). High-Output Insignia Siren This Clifford-engineered siren is more rugged than generic sirens and has these features: n Remote siren silencing: If triggered by a non-threatening event, you can silence the siren without remotely disarming. Press button 1 on the master remote or button on the companion remote while the siren is sounding. Two chirps confirm that the sensor activated the alarm and the system is remaining armed. Four chirps confirm that the system is still armed, but that the ignition is on or the hood, trunk or a door is open and that this may indeed be a genuine theft attempt. n Automatic noise abatement: Alarm sounding is limited to five siren duration cycles even if a door is left open in the wake of an intrusion. [. . . ] To add a new COMPANION remote control, use the features in column 4 to individually assign each button. NOTE 2: You'll hear two chirps to indicate all remotes have been cleared from memory. You must now add new/existing remotes with the "Add new remote control" feature and/or the "Other vehicle`s remote" feature. NOTE 3: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the ignition (you'll hear 3 chirps to confirm program mode exit). [. . . ]