User manual CAT EYE GAME BIKE CONTROL

[. . . ] Install the GAMEBIKE Controller by sliding it into the controller bracket. Reference: 1 GAMEBIKE bracket is compatible with all CAT EYE headlamps. 2 3 Controller bracket Controller bracket Handlebar Click GAMEBIKE Controller Connecting the controller to the GAMEBIKE Connect the pin jacks from the GAMEBIKE to the GAMEBIKE Controller. Caution Do not plug in/unplug the GAMEBIKE pin jack while "Playstation2" is turned on. This may result in a malfunction of the "Playstation2" unit. For brake button Cable GAMEBIKE MAIN UNIT To Brake button To Speed sensor To "Playstation2" For speed sensor For the unit 1 GAMEBIKE Controller E Caution · Before using this product, be sure to read the "Notes on using the GAMEBIKE Controller " and the "Notes on using the GAMEBIKE" in the GAMEBIKE Operation Manual. · Certain software packages whose packaging or documentation provides no indication of analog compliance or compatibility will not work in analog mode. · Certain software packages will not switch mode even if the analog mode switch is pressed. In the case of certain software packages, the mode switches automatically. Important: Depending on the software, GAMEBIKE operation sometimes takes precedence over the GAMEBIKE Controller and prevents operation of the controller. Reference: If the GAMEBIKE Controller is not connected to the GAMEBIKE, it can be used as a controller for "Playstation 2". [. . . ] Controller cover Controller 2 Connecting the device to Playstation2 This controller is compatible with the "Playstation2". Plug the connector of this device into the controller terminal located at the front of the "Playstation2". Consult the operating manual of the "Playstation2" unit, if necessary. E Important: If the GAMEBIKE does not operate after connecting it to the PlayStation2 unit, disconnect it and reconnect it again. "Playstation2" unit Controller connector Reference: It is possible for two players to play simultaneously by connecting two GAMEBIKEs or connecting to a general controller. 1P side To GAMEBIKE Controller 2P side How to adjust the GAMEBIKE · Adjusting the steering sensitivity Turn on the "Playstation2", then slide the steering sensitivity control of the GAMEBIKE Controller while operating the handle of the bicycle on the race screen to adjust the steering sensitivity as required. Caution Depending on the software, while moving the handlebar from Left to Right, the steering reaction on the game does not work. Min. L STEERING LEVEL SPEED LEVEL R SELECT ANALOG START STEERING LEVEL Speed sensitivity Slow Fast · Adjusting the speed sensitivity Turn on the "Playstation2", then slide the speed sensitivity control of the GAMEBIKE Controller while operating the pedal of the bicycle on the race screen to adjust the speed sensitivity as required. Caution Depending on the software, while pedaling, the speed of the game does not register. This will cause the game not to move forward. L STEERING LEVEL SPEED LEVEL R SELECT ANALOG START SPEED LEVEL Button Function change In the case of software with different button functions, change functions as follows: The buttons to which functions can be assigned are green, pink, red, blue, L1, L2, R1 and R2. <Operation> Keep pressing the SELECT button until the following steps are completed: 1. Press the blue (or pink) button depending on the function to be changed. The LED will change from constantly lit to blinking. 2. Press the default accelerator (or brake) button in the software currently being used. The LED will change stop blinking and will be lit continuously, signifying that the function change is now complete. (If analog mode is OFF, the LED will be off, signifying that the function change has been completed. ) · Revert to the original button function While pressing the SELECT button, press the speed button (blue) or brake button (pink). FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. 3 Symbols Legend E Symbol marks used for safety precautions in this manual The descriptions accompanying the following symbol marks in this manual refer to very important issues in terms of your safety and handling of the unit. You are strongly urged to observe these precautions carefully. Warning Caution Important Failure to observe this warning could result in serious injury or death. Failure to observe this warning could result in physical injury or damage to the GAMEBIKE. Operations which require caution, items which should be observed in particular as well as certain additionnal information are presented in this manual. This symbol mark denotes helpful information ensuring proper usage. Reference GAMEBIKE Controller usage cautions! Caution · It has been reported that, in rare cases, some people have experienced certain physical symptoms, for example muscle spasms or temporary loss of consciousness as a result of stimulation from strong light rapidly changing on-screen images. [. . . ] Send the device and warranty card to us directly, filling in the purchaser's name, address, date of purchase and a information regarding the malfunction. The warranty does not cover shipping charges incurred by the customer in returning the device to our service department. The product will be returned to the customer on completion of necessary repairs. Product Service Section 2-8-25, Kuwazu, Sumiyoshi-ku, OSAKA, 546-0041 Japan PHONE: 81-6-6719-7781 FAX: 81-6-6719-2362 E-mail address: Sales@cateye. co. jp Attn: CS/PR. LIAISON. Service & Research Address for North American Customers: CAT EYE Service & Research Center 1705 14 th St. [. . . ]