User manual CAT EYE CC-5000 (SOLAR 2)

[. . . ] Do not apply paint thinner, benzine, or alcohol, to avoid damages on the surface. · If there is mud, sand or the like clogs between the button and the body, the movement of the button may be disturbed. Softly wash away such objects with water. #169-6169 Bracket Sensor Kit for Aero Bar SPECIFICATIONS Applicable Cycle Sizes Applicable Fork Diameter The length of the wire Power Supply Battery Life 130cm - 229cm 11ø - 36ø (S:11 - 26ø L:21 - 36ø) 70cm Lithium Battery (CR1620/CR1616) x 1 Approx. [. . . ] To return the product, pack it carefully and remember to enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service. #169-6280 Universal Sensor Band (Address for service) CO. , LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan Attn. : CAT EYE Customer Service Section Service & Research Address for United States Consumers: CATEYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303-443-4595 Toll Free: 800-5CATEYE Fax: 303-473-0006 e-mail: CatEyeUSA@aol. com #166-5120 Wheel Magnet #169-6180 Lithium Battery (CR1620) E OPERATING INSTRUCTIONS A. Main Display (Speed) Sensor Pulse Symbol Mode Symbol Speed Scale Symbol Auto Mode Symbol Sub-Display (Selected Function) M (Mode) Button H. Sensor Band Screw Sensor Bands-A (S)(L) Sensor Bands-B Magnet Sensor Band Rubber Pad CA T EY E MOUNTING TO BIKE · The spokes must run correctly through the inside the magnet as in fig. 8. Choose a band that fits the fork diameter (S size for up to 24ø, L for oversize). Insert the band-B into the slit of the band-A, and put the rubber pad inside of the band-A(fig. Revise the number as desired according to the instructions in (3). sensor band B rubber pad screw sensor band A parallel Fig. 10 sensor fork Fig. 11 bracket outer cable Setting the clock time (Fig. 7) Press M button over 2 seconds to select , and stop it with S/S button. *When you press the SET button, the undisplayed seconds will turn to zero. For accuracy, set by the radio time signal. rubber pad magnet Fig. 8 sensor band A Fig. 9 Fig. 7 markingline of sensor magnet sensor rubber pad MEASURING AND DISPLAY FUNCTIONS screw cap Fig. 15 lever ODO DST Current Speed 0. 0(3. 0) - 65 mile/h(27inch) ±1 mile/h under31 miles/h This is always displayed on the main display and updated once a second. SPD ODO Total Distance (Odometer) 0. 0 - 9999. 9 mile ±0. 1 mile This is continuously measured until battery wears down or all clear operation is done. At 10, 000 miles(km), it returns to zero and counting begins anew. center of magnet about 2mm Fig. 13 Fig. 12 wire securing tape wire Fig. 14 HOW TO REPLACE THE BATTERY Turn main unit over, remove battery case cover with coin and insert a new lithium battery properly (CR1620 or CR1616) with the (+) pole upward (fig. 17), and close the cover securely. * Please make sure to do the All Clear operation after replacing battery, and to set the unit again. OPEN Fig. 16 DST CLOSE Trip Distance 0. 00 - 999. 99 mile ±0. 01 mile The trip distance from start to current point is displayed. DST Elapsed Time 0:00'00" - 9:59'59" ±0. 003 % Elapsed time is measured from start to current point, in units of hours, minutes and seconds. TM AVS Average Speed 0. 0 - 65. 0mile/h ±0. 3 mile/h The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99, 999 seconds) or 999. 99 miles (km). MXS Maximum Speed 0. 0(3. 0) - 65 mile/h(27inch) ±1 mile/h With Reset operation, it returns to zero and counting begins anew. Fig. 17 TM BUTTON FUNCTION · M button (Fig. 1) Changes the display in the order shown in fig. [. . . ] *If held over 2 seconds, 12-hour clock appears. MXS ODO DST TM AVS Fig. 1 AVS MXS · S/S button Starts and stops the measurement of trip distance and elapsed time. In Auto Function, this button is invalid. 12-hour clock time The current time is displayed by a 12-hour clock. 0:00' - 11:59' ±0. 003 % · SET Button This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear all present data and any irregularity. When pressed in stop state in each mode, the following can be revised. [. . . ]