User manual CANDY GVC 71013NB-

[. . . ] INSTRUCTION BOOK GVC 71013NB Condenser Tumble Dryer English Italiano Español 2 16 30 Porteguese 44 Français Dutch 58 72 INDEX Introduction Delivery Information Safety Reminders Use Installation The Laundry Ventilation Environmental Issues Gias Service Installation Electrical Requirements Adjusting the Feet Drain Hose Kit: Fitting Instructions Preparing the Load Clothes Preparation Do Not Tumble Dry Energy Saving Sorting the Load Drying Guide Controls and Indicators Selecting the Programme Door and Filter Opening the Door Filter Filter Care Indicator Water Container To Remove the Container Condenser To Remove the Condenser Operation Delay Start Function Cancelling and Resetting the Programme Cleaning and Routine Maintenance Cleaning the Dryer Technical Specifications Troubleshooting Customer Service Spares Gias Service 3 3 3 4 5 5 6 7 7 7 7 7 8 9 9 9 9 9 9 10 11 12 12 12 12 12 12 13 13 13 14 14 14 14 14 15 15 15 15 EN 2 INTRODUCTION Please read and follow these instructions carefully and operate the machine accordingly. This booklet provides important guidelines for safe use, installation, maintenance and some useful advice for best results when using your machine. Keep all documentation in a safe place for future reference or for any future owners. Delivery Information Please check that the following items are delivered with the appliance: ● Instruction manual ● Guarantee card ● Energy label Check that no damage has occurred to the machine during transit. [. . . ] It can be used only with the selection of: Mix&Dry, Shirts and Time Programmes. Delay Start Button – Allows the user to delay the start of the drying cycle (see details of Operation ). Acrylic and Synthetic Button –Press to select the type of fabrics to dry Acrylic and synthetics, when pressed Acrylic Synthetics option is activated and the indicator lights up. Memo Button – Allows user to record the programme by pressing simultaneously the AntiCrease and the Acrylic Synthetic buttons for 3 seconds, after 2 minutes duration of the chosen programme/option. Empty Water indicator – Lights when the water container is full. program Display – Related indicator lights when a auto programme has been selected. Refresh – The indicator lights up when the programme starts the cool down stage. SELECTING THE PROGRAMME The Candy Sensor Dry machine gives many options for drying the laundry to suit all circumstances. The table on the next page lists the programmes and the function of each programme. For small loads and separate items or pre-dried fabrics with low moisture content, use the timed programmes. If the sensor does not detect the item the dryer will only operate for 10 minutes before going into cooldown. If the load is too large or too wet to tumble dry the dryer will automatically go into cooldown after approximately 3 hours. In these cases we advise to use a time cycles between 30 and 75minutes depending on the load size and dryness required, and select high or low heat depending upon the fabric type. EN 10 SELECTING THE PROGRAMME PROGRAMME Perfect Home Store Dry Hang Dry Iron Dry Anti Crease DESCRIPTION Select the degree of dryness that you require. This range from for bath towels and bathrobes, through for items that will be put away without ironing, to the programme that leaves the laundry suitable for ironing. The dryer will heat the load for 9 minutes followed by a 3 minute cool down period and is especially good for garments which may have been left for some time prior to ironing, in a linen basket for example. Garments may also become stiffened when dried outside on a washing line or inside on radiators. This programme relaxes the creases in the fabric making ironing quicker and easier. A gentle programme specially created to get woollens softer after air-drying. This delicate warm air cycle, lasting 12 minutes, can also be used to get woollens 'refreshed' after being stored in the wardrobe. This is a special timed program for shirts of max load of 3kg (78 minutes). the Rapid 40' programme allows a drying cycle to be completed quickly. [. . . ] However, a charge may be made if any of the following applies to your machine: ● Is found to be in working order. — Has not been installed in accordance with the installation instructions. gIAS Service For service and repairs call your local GIAS Service engineer. The manufacturer declines all responsibility in the event of any printing mistakes in this booklet. [. . . ]