User manual BOSE SL2 WIRELESS SURROUND LINK
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSE SL2 WIRELESS SURROUND LINK. We hope that this BOSE SL2 WIRELESS SURROUND LINK user guide will be useful to you.
You may also download the following manuals related to this product:
BOSE SL2 WIRELESS SURROUND LINK (2178 ko)
Manual abstract: user guide BOSE SL2 WIRELESS SURROUND LINK
Detailed instructions for use are in the User's Guide.
[. . . ] It is neither designed nor tested for use outdoors, in recreation vehicles, or on boats. this product conforms to the EMC Directive 89/336/EEC , to the Low Voltage Directive 73/23/EEC , and to the RTTE Directive (99/5/EC). Read these instructions  for all components before using this product. Do not use this apparatus near water  Do not use this product near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or anywhere else that water or moisture are present. [. . . ] If your speakers are part of an Acoustimass® speaker system, you need to set the switch on the bottom of the SL2 transmitter to Other (Figure 2). For use of a LIFESTYLE® system with the SL2 Wireless Surround Link, the current default switch setting is optimal. Important note: Running the ADAPTiQ® audio calibration system, which is provided with your LIFESTYLE® system, helps ensure the most accurate sound from your system. Be sure to use it after the SL2 is connected and your surround speakers are in the final position. the SL2 transmitter , identified on the label , is also distinguished by a single input jack (see Figure 3 on page 6). Place the SL2 transmitter within 6 1/2 feet (2 meters) of the Acoustimass® module. Place the SL2 receiver at the same end of the room as your surround speakers. Upright (neither upside down nor on a side) on the floor or other flat, stable surface. Note: If you experience any problem with communications between the SL2 transmitter and receiver, positioning them within line of sight to each other may be helpful. For further suggestions on how to deal with such problems, refer to "Troubleshooting" on page 9. Transmitter power pack AC power jack Receiver power pack Before you plug either of the supplied power packs into the wall, make all the other connections. Use the supplied transmitter cable to connect the SL2 transmitter to your Acoustimass® module, as follows (Figure 4): 1. Insert the single connector at one end of the cable into the input jack labeled Acoustimass Module on the back of the SL2 transmitter. Insert the green connector marked LR into the jack labeled Left Rear or Surround L. Connect the cable end of the transmitter power pack to the small jack labeled DC Power on the back of the SL2 transmitter. When the power supply is plugged in, a Status LED on the back of the transmitter blinks green until it links to the receiver. It then lights a solid orange until there is an audio signal to transmit. Or, you may prefer to use the longer surround speaker cables that came with your speakers. Note: To use the SL2 supplied cables with Jewel Cube® speakers, first attach a Jewel Cube adapter to each cable as described in "To adapt the surround speaker cable for Jewel Cube® speakers" on page 8. To make the receiver connections Using the supplied cables, follow the steps below: 1. Insert the RCA connectors into the jacks on the back of the SL2 receiver (Figure 5). For details on how to set up and make connections to your surround speakers, refer to the owner's guide provided with them. [. . . ] Return product with proof of purchase from an authorized Bose dealer directly to Bose Corporation. If you elect to return the product directly to Bose Corporation, the following procedures must be followed: Contact Bose Corporation at 1-800-367-4008 for return authorization number, specific return and shipping instructions, which will include but may not be limited to: Properly packing the product in the original carton for shipping. If you need a new carton, contact Bose Corporation for free packing material and box. Return product with proof of purchase from an authorized Bose dealer to a Bose Service Agency. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSE SL2 WIRELESS SURROUND LINK
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSE SL2 WIRELESS SURROUND LINK will begin.