User manual BOSCH SMI 63M52EU/44 SUPPLEMENT

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSCH SMI 63M52EU/44. We hope that this BOSCH SMI 63M52EU/44 user guide will be useful to you.


BOSCH SMI 63M52EU/44 SUPPLEMENT: Download the complete user guide (740 Ko)

Manual abstract: user guide BOSCH SMI 63M52EU/44SUPPLEMENT

Detailed instructions for use are in the User's Guide.

[. . . ] This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Sears, Roebuck and Co. , D/817 WA, Hoffman Estates, IL 60179 If you want your water softener professionally installed, talk to your Sears Salesman. He will arrange for a prompt, quality installation by Sears Authorized Installers. SEARS INSTALLATION POLICY All installation labor arranged by Sears shall be performed in a neat, workmanlike manner in accordance with generally accepted trade practic es. [. . . ] Without brine, the resin bed does not regenerate and you will have hard water. If the storage tank is full of salt, it is hard to tell if you have a salt bridge. Hold a broom handle, or like tool, up to the softener as shown in FIG. Make a pencil mark on the handle, 1 or 2 below the top height of the rim, as shown. If a hard object is felt before the pencil mark gets to the top of the tank, it's most likely a salt bridge. Do not try to break the salt bridge by pounding on the outside of the salt tank. 9 SALT BRIDGE push tool into salt bridge to break 1" ­ 2" Pencil Mark Broom Handle Salt Salt Bridge Water Level 14 SECTION 3 3B. CARE OF YOUR SOFTENER KEEPING THE WATER SOFTENER CLEAN NOTE: Never use cleaners having ammonia or abrasives. They may scratch and dull the surface. COVERS To keep your new Sears water softener looking nice, apply a coat of paste wax and repeat once a year. This small unit moves brine from the salt storage tank to the resin tank during regeneration. If it becomes plugged with sand, silt, dirt, etc. , the softener will not work and you will get hard water. Be sure the softener is in service cycle (no water pressure at nozzle and venturi). If, after making the checks, your softener still does not work right, call your Sears Service Department, or call toll free, number 1-800-426-9345 for telephone assistance. If an error code is not dispIayed, press and hold the SELECT button until (example: 000- -) shows in the display. If any other SR number shows, the softener computer is working on incorrect input and would probably be the cause of the problem. Then press select to return a flashing 12:00 AM display, and reset the timer, page 6. PROBLEM NO SOFT WATER CAUSE No salt (or salt bridged) in the storage tank CORRECTION Refill with salt, or break the salt bridge (page 14). Press ON/OFF-HOLD (RECHARGE NOW) button and hold for 3 seconds to start a regeneration (see page 10). With the power back on, look at the time display and read PROGRAM MEMORY, page 10. In a 3-valve bypass, open the inlet and outlet valves, and be sure to fully close the bypass valve. The drain hose must not have kinks, sharp bends, or be raised too high above the softener (see page 16 in your installation manual). Press and release the SELECT button until HARDNESS shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown on your water analysis report. [. . . ] WATER FLOW THROUGH THE SOFTENER VALVE BRINING AND BRINE RINSE CYCLES After fill, timer/switch action allows the motor to turn the rotor and disc into BRINING position. Suction, created by the nozzle and venturi, draws brine from the salt storage tank and injects it into the resin bed via the bottom distributor. When the brine valve closes to end brine draw, water flow continues in the same directions to slowly RINSE brine from the resin bed and to the drain. BACKWASH CYCLE Timer/switch action again allows the motor to turn the rotor & disc to place the valve in BACKWASH, stopping water flow to the nozzle. Water is routed down and out the bottom distributor, up through the bed, and out the top distributor to the drain. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSCH SMI 63M52EU/44




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSCH SMI 63M52EU/44 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.