User manual BISSELL 3910

[. . . ] Momentum Cyclonic BAGLESS VACUUM USER'S GUIDE 3910 SERIES 220-240V 3 Safety Instructions Product View Assembly Operation Maintenance and Care Troubleshooting Consumer Services Replacement Parts Warranty 4 5-6 6-9 10-16 17 18 19 20 ug603-2377_3910E_207. indd 1 2/7/07 4:03:31 PM Thanks for buying a BISSELL vacuum We're glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] · Slide the brush off to use the upholstery tool on cushions, draperies and fabrics. 8 www. bissell. com ug603-2377_3910E_207. indd 8 2/7/07 4:03:41 PM Operation Crevice Tool: Use in tight narrow spaces. Curved Hose Wand: Use with desired attachment for a longer reach or for cleaning hard to reach places. TurboBrushTM: Use rotating brush action for small areas such as stairs and upholstery. NOTE: Press gently when using the TurboBrush to maximize cleaning. Too much pressure will cause the brush to stop rotating. Tip: Hair, string and small objects can block the vacuum hose or tools. To use your vacuum, remove the cord and plug it into an electrical outlet. For your convenience, there are two quick release cord wraps for easy cord removal. There is also a cord clip that is part of the upper cord wrap where you can attach the cord when vacuuming. Unplug power cord by grasping the plug (NOT the cord) and disconnect from outlet. Be sure to first return the quick release cord wraps back to their original position before wrapping the cord. 4. Slide the Lock `n Seal Lever to the "Unlock" position. Grasp handle and pull the dirt container straight out to remove from the vacuum. Empty dirt into garbage container. NOTE: Emptying the dirt container after every use will help prevent overfilling and ensure that the vacuum is ready to go the next time you clean. 4. Unlock 10 www. bissell. com ug603-2377_3910E_207. indd 10 2/7/07 4:03:43 PM Maintenance and care Cleaning the pre-motor and post-motor HEPA media filter 1. If the filter becomes dirty, pull out the tray, lift out the foam filter pad and clean it. NOTE: The pre-motor filter may be hand washed in cold water with mild detergent. The post-motor HEPA media filter Washable assists in the filtration process to Pre-Motor return clean air to the room. If the filter becomes dirty, open the door, remove the filter and replace. This filter is NOT washable and must be replaced when it becomes dirty. Post-Motor HEPA Media Filter 3. WARNING: Do not operate vacuum cleaner with damp or wet filters or without all filters in place. www. bissell. com 11 2/7/07 4:03:44 PM ug603-2377_3910E_207. indd 11 Maintenance and care Check rotating floor brush and drive belt You should check your vacuum cleaners rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hamper its ability to effectively clean your carpet. Unplug the vacuum from electrical outlet. 3. WARNING:injury To reduce the risk of from moving parts, turn power switch off and disconnect plug from electrical outlet. 2. Place handle in low position and turn vacuum cleaner over so bottom side is facing up. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. Clean strings, hair and other debris from motor pulley and drive belt areas. [. . . ] Incorrect height adjustment Hose not attached to suction opening Twist 'n Snap hose not securely attached Crack or hole in hose Broken or worn drive belt Rotating floor brush bristles worn Rotating floor brush jammed Clog in vacuum Dirt container full Remedies 1. TurboBrush is clogged or debris is wrapped around the brush roll Vacuum cleaner is difficult to push Possible causes 1. Adjust powerfoot to correct height setting Visible dirt escaping from cleaner Possible causes 1. Pull out and re-insert dirt container correctly Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. www. bissell. com 17 2/7/07 4:03:47 PM ug603-2377_3910E_207. indd 17 BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. [. . . ]