User manual BESAFE IZI KID

[. . . ] · When the child weighs over 18 kg or the shoulder height grows above the highest position of the shoulder straps, the child must change to a group 2/3 seat. Although it may look undamaged, if you were to have another accident, the seat may not be able to protect your child as well as it should. ! ! It is important that you read this user manual BEFORE installing your seat. Incorrect installation could endanger your child. Contents Vital information Preparing to install Rearward-facing in the back or front seat: preparation Rearward-facing in the back seat: installation Rearward-facing in the front seat: installation Removing the seat Positioning of the child Sleeping position Removing and refitting the cover Cleaning instructions Warning: potential misuse Important advice Guarantee Point of sale information 3 4 5 9 12 14 15 16 17 19 20 21 22 23 2 3 Preparing to install Crucial parts Release handle head rest Adjustable head rest Harness shoulder straps Harness buckle Belt tension indicator (if applicable) Central adjuster Reclining lever Front brace Belt guiding hook Ratchet for front brace Belt guiding horns Rearward-facing in the back or front seat: preparation It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG. 1- When mounting in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible. [. . . ] Place the hip belt over the base of the seat behind the belt guiding horns on each side (see green arrows 1 and 2 in fig. 13- Pull the hip belt forwards and over the belt guiding hook on the seat base (see green arrow 3 in fig. 9). (9) 2 4 1 3 (8) ! · To continue with rearward-facing installation in the back seat, go to page 9. · To continue with rearward-facing installation in the front seat, go to page 12. 8 14- Pull the shoulder/diagonal belt round the belt guiding horn on the side of the base (see green arrow 4 in fig. Tension the shoulder belt. 9 15- Pull out the shoulder belt and make it into a loop (10a). 16- Thread the loop through the metal part of the red belt block (10b). 18- Tighten the belt by pulling the top part down (10d). (10) 20- Connect the anchor belts with the child seat. 22- Lock the floor support with the locking bolt (14). (13) (14) a b c d 23- Positioned in the back seat of the vehicle, you should, if possible, push the front seat of the vehicle backwards, so that it is in contact with the child seat. If it is not possible to obtain contact with the child seat, push the back rest of the front seat of the vehicle forward so that the distance between child seat and back rest of the front seat of the vehicle is minimum 25 cm. Adjustments of the front seat might bring slack in the anchor belts; tighten the anchor belts again. Practical Advice If the seat is standing too upright: Push the front seat forward, follow the described installation, by pulling the anchor belts as much as possible before you lock the height of the foot support, the car seat cushion will be compressed and you will achieve a more reclined position for your child. Finally lock the foot support. (12) (11) ! ! Rearward-facing in the back seat 19- Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat (10). 10 11 Rearward-facing in the front seat: installation With the anchor belts in place the installation can continue: 7- Place the seat sideways into the car with the front brace towards you. 8- Turn the seat into the right position (with the front brace against the back rest). 9- To enlarge the space for the legs of the child, you can move the front brace outwards with the ratchet. 10- In the front seat of the vehicle, you should position the seat against the dashboard. The floor support must go through the belt loop and the belt loop must be led into the hook on the floor support (15). 12- Position the 3 point car belt. Place the hip belt over the base of the seat behind the belt guiding horns on each side. Tension the shoulder belt. (16) 13- Pull out the shoulder belt and make it into a loop (17a). 14- Thread the loop through the metal part of the red belt block (17b). 16- Tighten the belt by pulling the top part down (17d). (17) (15) a b c d (18) Rearward-facing in the front seat ! 12 13 17- Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat (19). Positioning of the child 1- Position of the shoulder straps: Check that the shoulder strap slots are levelled with your child's shoulders (22). [. . . ] · BeSafe advises that child seats should not be bought or sold second-hand. It has not been designed for home use and can only be used in a vehicle. Practical advice When the child seat is mounted in the car check all the areas where the child seat might touch the interior. We recommend using a (BeSafe) protection cover in these places to avoid cuts, marks or discolouration on the interior of the vehicle, especially in vehicles with leather or wooden interior. 20 21 Point of sale information Notice for REARWARD-FACING installation · This is a semi-universal Child Restraint System. [. . . ]