User manual BESAFE IZI COMBI

[. . . ] · We recommend to use the seat as long as possible in the rearward-facing installation. · We recommend that this seat is used only for children who can sit upright, so not younger than 6 months. · For children under 1 year and/or under 10 kg weight, we recommend that the most reclined sitting position and the body hugger and seat cushion are used. · When the child weighs over 18 kg or the shoulder height grows above the highest position of the shoulder straps, the child must change to a group 2/3 seat. [. . . ] 22- Lock the floor support with the locking bolt (14). (13) (14) a b c d 23- Positioned in the back seat of the vehicle, you should, if possible, push the front seat of the vehicle backwards, so that it is in contact with the child seat. If it is not possible to obtain contact with the child seat, push the back rest of the front seat of the vehicle forward so that the distance between child seat and back rest of the front seat of the vehicle is minimum 25 cm. Adjustments of the front seat might bring slack in the anchor belts; tighten the anchor belts again. Practical Advice If the seat is standing too upright: Push the front seat forward, follow the described installation, by pulling the anchor belts as much as possible before you lock the height of the foot support, the car seat cushion will be compressed and you will achieve a more reclined position for your child. Finally lock the foot support. (11) ! ! Rearward-facing in the back seat 19- Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat (12 ). (12) 10 11 Rearward-facing in the front seat: installation With the anchor belts in place the installation can continue: 7- Place the seat sideways into the car with the front brace towards you. 8- Turn the seat into the right position (with the front brace against the back rest). 9- To enlarge the space for the legs of the child, you can move the front brace outwards with the ratchet. 10- In the front seat of the vehicle, you should position the seat against the dashboard. The floor support must go through the belt loop and the belt loop must be led into the hook on the floor support (15). 12- Position the 3 point car belt. Place the hip belt over the base of the seat behind the belt guiding horns on each side. Tension the shoulder belt. (16) 13- Pull out the shoulder belt and make it into a loop (17a). 14- Thread the loop through the metal part of the red belt block (17b). 16- Tighten the belt by pulling the top part down (17d). (17) (15) a b c d (18) Rearward-facing in the front seat ! 12 13 17- Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat (19). Forward-facing belt installation It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG. 1- When mounting in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible. 2- When mounting in the front seat of the vehicle, adjust the back rest in an upright position. 5- Release the release handle at the back of the head rest and push the head rest down while keeping the head rest upright (23). (23) (22) ! (19) 18- Connect the anchor belts with the child seat. 20- Lock the floor support with the locking bolt (21). (20) (21) Removing the seat 1- If the seat is installed in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible. 2- Move the front brace inwards with the ratchet, not further than the stop sign. 3- Remove the locking bolt from the floor support, adjust the floor support in the highest position and lock again with the locking bolt. 7- Remove the anchor belts from the vehicle. 14 6- Pull the hip belt around the bottom base of the seat and click the car belt in the buckle (28). [. . . ] · BeSafe advises that child seats should not be bought or sold second-hand. It has not been designed for home use and can only be used in a vehicle. Practical advice When the child seat is mounted in the car check all the areas where the child seat might touch the interior. We recommend using a (BeSafe) protection cover in these places to avoid cuts, marks or discolouration on the interior of the vehicle, especially in vehicles with leather or wooden interior. 22 23 Guarantee · All BeSafe products are carefully designed, manufactured and tested. [. . . ]