User manual BEMIS 736200

[. . . ] This equipment is not designed for maritime use or for use in mobile installations such as caravans or aircraft. However, under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele Technical Service Department with specific requirements. This dishwasher must be installed under a continuous countertop secured to adjacent cabinetry. [. . . ] Tipping the machine slightly to the rear, if possible, will make adjusting the front legs easier. Make sure the machine is level when adjustments are complete. ^ Place the skis, with the ratchet at the rear, under the dishwasher legs. 13 Installation 3. Install the dishwasher under the countertop The dishwasher must be installed so that the water and electricity supplies can be accessed through an adjacent cabinet. ^ Make certain that there are no rough edges that could damage the power cord or hoses. If metal cabinets are used, place the supplied rubber grommet around the edge of the opening before passing the cable through. , WARNING - Fire hazard Do not cover or crush the plug of an electric appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug. Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which may cause overheating. The floor of the cut out where the dishwasher will be installed should be even in height with the surrounding kitchen floor. Plywood can be secured to the floor to make the two areas even. ^ Slide the machine into the opening, making sure the electrical cable and hoses can reach their connection points without kinking. The left side of the optic indicator reflector and the optic indicator must align. The drain hose connection at the rear of the dishwasher can be turned to allow the hose to be angled to the right or left. ^ Exercise care when sliding the dishwasher in or out, to prevent damage to the power cord or hoses. ^ Make a 2" x 4" (5 x 10 cm) cut out in the side or bottom of the cabinet adjoining the dishwasher. Using this method on larger openings may damage the machine and cause leaks. ^ Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet. ^ Secure the dishwasher to the adjacent cabinets using the supplied screws and bushings. Make sure a bushing is placed over the screw before inserting it into its mounting hole. If the door remains in this position when released, the springs are adjusted correctly. If the door closes on its own, the tension on the springs need to be decreased. ^ To adjust the door springs use a T20 Torx or a small slotted screwdriver and turn the screw located behind the door in the upper front strip, on the left hand side of the dishwasher. ­ turn clockwise to increase the tension ­ turn counterclockwise to decrease the tension. Note: If the door springs can not be adjusted enough (the door falls), the custom door panel is too heavy. Call your Miele dealer or the Technical Service Department for advice on stronger door springs. 23 Installation 9. Make the plumbing connections An air gap is built into the water inlet system to prevent potable water from mixing with waste water. The dishwasher can heat its own water to the temperatures required by the wash program. This allows the option of connecting the machine to either a hot or cold water source. [. . . ] If there is any question about the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: USA 1-800-999-1360 CDN 1-800-565-6435 28 Installation Power outlet The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An opening through the partition between the compartments of 1 1/2" (3 to 4 cm) can be made to allow the plug to pass through. Permanent Connection (Hard Wiring) For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher, behind the toekick and service panel. Pass the permanent power supply cable through the strain relief and secure it to the terminal box. [. . . ]