User manual BELSON PT7434

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BELSON PT7434. We hope that this BELSON PT7434 user guide will be useful to you.


BELSON PT7434 : Download the complete user guide (711 Ko)

Manual abstract: user guide BELSON PT7434

Detailed instructions for use are in the User's Guide.

[. . . ] When you dispose of the battery, you must obey the law in the relative area or country. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] (1 page 24) Input signal setting indicator When Input-A is selected: Shows "Auto" or "Input-A Signal Sel. " setting in the SET SETTING menu. When Video or S-Video is selected: Shows "Auto" or the "Color System" setting in the SET SETTING menu. RESET button 1 Press MENU. The menu window appears. The menu presently selected is shown as a yellow button in the column on the left. SET SETTING S m a r t A PA : Auto Input Search: Input-A Signal Sel. : Color System: Pow e r S av i n g : IR Receiver: Lamp Timer Reset On Off Component Au t o Off F ro n t & R e a r Input-A 2, 3, 4 1 Display items The input signal and input signal setting indicators are displayed on the upper right corner of the menu window. Input signal indicator 2 Press M/m to select a menu, and press , or . Press M/m to select an item you want to set or adjust and press , or . The items that can be set appear in the pop-up menu, adjustment menu, or in the next menu window. Input signal setting indicator 3 Input signal indicator Shows the selected input channel. You can hide this indicator using "Status" in the MENU SETTING menu. 33 Pop-up menu Menu MENU SETTING Status: L a n g u ag e : M e nu Po s i t i o n : S t a r t U p I m ag e On English To p l e f t Bottom Left Center To p R i g h t Bottom Right To clear the menu Setting items Input A Press MENU. The menu disappears automatically if a button is not pressed for one minute. A To reset the items that have been adjusted Select an item that you want to reset, then press RESET on the remote control. The message "Complete!" appears on the screen and the setting of the item that you have selected is reset to its factory preset value. Items that can be reset are: · "Contrast, " "Brightness, " "Color, " "Hue" and "Sharpness" in the "Adjust Picture. . . " menu of the PICTURE SETTING menu · "Dot Phase, " "H Size, " and "Shift" in the "Adjust Signal. . . " menu of the INPUT SETTING menu Storage of the settings The settings are automatically stored in the projector memory when the button is pressed. If no signal is input If there is no input signal, the message "Cannot adjust this item. " appears on the screen. Adjustment menu Next menu window Menu PICTURE SETTING ADJUST PICTURE Contrast: Brightness: Gamma Mode: C o l o r Te m p . : 80 50 Off High Setting items Input A S t a n d a rd 4 Make the setting or adjustment of an item. Wide Mode: Over Scan: Normal Off Using the Menus Setting items Adjust Signal. . . Dot Phase Functions Adjusts the dot phase of the LCD panel and the signal output from a computer. Adjust the picture further for finer picture after the picture is adjusted by pressing the APA key. H: As the setting for H (horizontal) increases, the picture moves to the right, and as the setting decreases, the picture moves to the left. V: As the setting for V (vertical) increases, the picture moves up, and as the setting decreases, the picture moves down. You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an video signal (preset memory numbers 1 to 11) is input. Normal: A picture with normal 4:3 aspect ratio is displayed in the center of the screen to fill the vertical screen size. Full: A picture squeezed to 4:3 is displayed with the correct aspect ratio. Zoom: A normal 16:9 aspect ratio picture (SD signal only) is enlarged vertically and horizontally in the same ratio to fill the screen. Wide Zoom: A 4:3 aspect ratio picture (SD signal only) is enlarged over the entire screen properly. [. . . ] · When a signal other than the preset signals shown above is input, the picture may not be displayed properly. · When an SXGA+ signal is input, the image may extend beyond the edges of the screen. In this case, input a signal with no black edges around the image, and disconnect and reconnect the cable or select the input signal by pressing INPUT. · If the resolution of the input signal is different from the panel resolution, the input signal is not displayed in its own resolution, and letters or lines may be uneven. 55 Installation Diagram Floor Installation (Front Projection) Distance between the front of the cabinet and the center of the lens Foremost part of the cabinet Wall Front of the lens 14. 6 (19/32) Center of the lens Center of the screen Floor Unit: mm (inches) * Adjuster not stretched, and the V Keystone function has been done. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BELSON PT7434




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BELSON PT7434 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.