User manual BELSON MH2002-MH2007

[. . . ] The front is designed to accept a custom made panel, matching the existing kitchen cabinets. "U" dishwashers The built-under ("U") dishwashers use the integrated ("i") dishwashers as the basic machine. By using a GDU decor kit the "i"dishwasher can be converted into a "U" model dishwasher. GDU installation instructions are included in a separate pamphlet supplied with the decor kit. 5 Guide to the appliance View of the machine 1. Upper spray arm (not visible) 2. [. . . ] Turn the program knob clockwise past the 12 o'clock position, until the desired program is reached. The new program will start. Changing programs. Wash temperatures can be changed while a program is running, by turning the Temperature selector. If a different wash program is desired, follow the above procedure. Turn the Program knob clockwise to the desired program. Turning off. When finished, the program will stop automatically. Your Miele dishwasher is designed to shut off the water flow and drain the machine in the rare event of a valve failure. In order for this function to be active, the door must be shut, a temperature must be selected, and the program knob must be in the "End" (12 o'clock) position. Select the desired temperature, or the "RINSE & HOLD" program. The wash program will begin. 32 Operating the dishwasher Program sequence indication. During the wash program, the program knob will move around the dial and show which section of the wash cycle has been reached. ­ Pre-wash (not shown) ­ Main wash ­ Interim rinse ­ Final rinse ­ Drying The dial will remain stationary during the heating stages of the wash and rinse cycles, until the required temperatures have been reached. When the program has been completed, the dial will be in the "End" position. If the dishes are not immediately needed, leaving the door closed will allow the fan to run a few minutes longer to remove any remaining moisture. The "RINSE & HOLD" program has been completed when the program dial stops just before the starting point of the "INTENSIVE" program. Program interruption A program is interrupted as soon as the door is opened. If the door is closed again, the program will proceed from its previous position. Replace and secure the combination filter. 38 Cleaning and care Cleaning the water intake filter. The water valve housing on the inlet hose contains electrical components and should not be immersed, or run through water. A filter is incorporated in the intake hose that is attached to the dishwasher's main shutoff valve. If your water supply is hard, or the pipes contain sediment; this filter may clog and prevent sufficient water from entering the wash cabinet. It can be cleaned as follows: Cleaning the filter. Disconnect the dishwasher from the electrical supply (unplug it or shut off the circuit breaker). Turn off the main shutoff valve and unscrew the intake hose. Remove the filter using needle nose pliers and clean it by rinsing under running water. Screw the intake hose back onto the water valve, making certain it is not cross-threaded. If your water supply contains a large number of insoluble substances, we recommend installing a filter between the valve and the intake hose connection. These filters can be obtained from the Miele Parts Department. 39 Cleaning and care Cleaning the wash cabinet. Generally the wash cabinet is selfcleaning, provided that the correct amount of dishwasher detergent is used. If lime scale or grease deposits form, they can be removed with a special dishwasher cleaner available from the Miele Parts Department. Cleaning the control panel. The control panel can be cleaned using a damp cloth and mild detergent. Do not use abrasive, all purpose, or glass cleaners, as their use may damage plastic surfaces. Cleaning the door panel. Plastic laminate panels should be cleaned using a suitable, non-abrasive cleaning agent, or mild soapy water. Panels made from wood should be cleaned using a soft damp cloth and an appropriate wood cleaner. Cleaning the door and the door seal. Wipe the door seal with a damp cloth to remove any food particles. [. . . ] If this is not possible, it can be installed horizontally as shown, provided the hose exit remains beneath the main body of the box (see illustration). (The "lightning bolt" should be above the "arrow" when the installation is complete). The valve box should also be installed so that it is at least 8" (24 cm) above the floor (or base of the cabinet), and so the excess coiled hose will remain lower than the box at all points. A 2" x 4" (60 x 115 mm) cutout in either the side or bottom of the cabinet adjoining the dishwasher is necessary if the valve box needs to be passed through. Plumbing Existing plumbing: If the standard 3/8" copper plumbing for a dishwasher already exists with a compression fitting and valve as pictured: Cut the 3/8" copper tubing after the valve. Install the 3/8" compression to 3/4" MHT (Male Hose Thread) adapter (supplied with the machine), as illustrated. [. . . ]