User manual BELSON C21-1-6

[. . . ] 13) Learn to get to know the parts which make up your dishwasher, you will use it better for it. This is where you will find the description of the controls and the internal parts. 14) This page includes useful tips to help you load your dishwasher correctly and make the most of all the available space. 15) After loading the dishes, you need to select the right wash cycle and measure out the correct dose of detergent and rinse aid. [. . . ] Warning Three-in-one dishwasher tablets are now available on the market, and combine detergent, salt and rinse aid all in one. If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the formation of white streaks on your dishes or on the interior of the appliance. Using a three-in-one product means it is no longer necessary to put rinse aid into the relevant container. If you want to achieve perfectly dry dishes, you may add rinse aid as long as the dosage adjuster is set to no. In any case, please read the manufacturer's instructions on the packet. If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain number of cycles. 16 ARISTON DISHWASHER - Instructions for installation and use A wash cycle for every degree of soil Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. Select the right wash cycle D ISHWASHER Select the right wash cycle for your dishes. Selecting the most suitable wash cycle for the load ensures clean dishes and a more convenient use of water and electricity. Salt, rinse aid, the right amount of detergent and the correct wash cycle: this is the formula to get the best results and to keep your dishwasher in shape &\FOH &\FOH VHOHFWLRQ LQVWUXFWLRQV &\FOH GHVFULSWLRQ 'HWHUJHQW IRU SUH ZDVK  ZDVK 5LQVH $LG :DVK F\FOH GXUDWLRQ WROHUDQFH “ ZLWKRXW H[WUD GU\LQJ  Very dirty dishes and pans (not to be used for delicate items) 6XSHU :DVK Cycle for normally dirty pans and dishes.  1RUPDO Environmentally-friendly cycle, with low energy consumption levels, suitable for normally dirty pans and dishes. If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher. Your dishwasher can be supplied with hot water from the mains supply (if you have a central heating system with radiators) at a temperature of no more than 60°C. In this case, the wash cycle time will be about 15 minutes shorter and the wash will be slightly less effective. The connection must be made to hot water supply following the same procedures as those indicated for the cold water connection. Anti-flooding protection Your dishwasher is provided with a special system which blocks the water supply in the event of leaks inside the appliance. It is further equipped with a water inlet hose that can withstand extremely high pressures and that turns bright red in the event of breakage. Safety in the event of flooding is ensured by the second clear hose that contains the former and thus highlights the latter when it has turned bright red. It is vital that you check it on a regular basis: if you see it has turned bright red, then you know you have to replace it as soon as possible. Fit the drain pipe into a drain line with a minimum diameter of 4 cm or place it over the sink. The part of the pipe marked with the letter A should be between 40 and 100 cm above the ground. [. . . ] The food particles are removed from the wash water, allowing it to be recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the larger food particles trapped inside the cup “C” and the semi-circular filter A after each wash; pull the cup handle upwards to remove them. The entire filter assembly should be cleaned thoroughly once a month: cup C + semi-circular filter A + cylindrical filter B. Reassemble the filter parts (as shown in the figure) and reinsert the whole assembly into the dishwasher. [. . . ]