User manual BELSON BP8408

[. . . ] 12) Learn to get to know the parts which make up your dishwasher, you will use it better for it. This is where you will find the description of the controls and the internal parts. 13) This page includes useful tips to help you load your dishwasher correctly and make the most of all the available space. 14) After loading the dishes, you need to select the right wash cycle and measure out the correct dose of detergent and rinse aid. [. . . ] You can modify the wash cycle in progress, if it has only just started. Keep the RESET button "R" pressed for about 5 seconds: a prolonged beep will sound, followed by three short beeps. Indicator light "G" will turn off and at this stage, all the settings will have been cancelled. If on the other hand you want to cancel the delay set and you want the cycle to start immediately, press button "D" repeatedly until the cycle starts and indicator light "G" corresponding to the cycle start phase comes on. Dual function of indicator lights "G" 1) flashing to indicate a delayed start: to remind you that you have set a delayed start; 2) on and not flashing beneath the cycle phase symbol: meaning the cycle has started and is in the phase indicated by the symbol. If opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. 14 ARISTON DISHWASHER - Instructions for installation and use Only use specific dishwasher detergents. Detergent and rinse aid D ISHWASHER Useful tips • Use the right amount of detergent: if you use too much, you will not get cleaner dishes, but just more environmental pollution. The detergent should be poured into the two containers C and D up to the rim. If you prefer to use the detergent in tablet form, then place one inside the container “D” and close the lid. Check whether there is any detergent residue on the edges of the dispenser. ARISTON DISHWASHER - Instructions for installation and use 17 D ISHWASHER Installation After having bought or moved your dishwasher to another home, a correct installation ensures that your dishwasher will operate smoothly and efficiently. Your dishwasher, you can even Your dishwasher can be supplied place it so that its sides or back with hot water from the mains panel are side by side with furniture supply (if you have a central heating or up against the wall. The system with radiators) at a tempedishwasher is provided with water rature of no more than 60°C. Supply and drain hoses, which can In this case, the wash cycle time be directed towards the left or right will be about 15 minutes shorter to facilitate appropriate and the wash will be slightly less installation. This dishwasher model can be built The connection must be made to under a single worktop (please read hot water supply following the the relevant instruction sheet). Adjust the feet by screwing them in Fit the drain pipe into a drain line or out depending on how high you with a minimum diameter of 4 cm want it and to level it so that it is or place it over the sink. If the special plastic elbow provided (see appliance is level, it will help ensure figure) to position it in the best Electrical connection. The part of the pipe First of all, check that the mains marked with the letter A should be voltage and frequency values Cold water connection. Between 40 and 100 cm above the correspond to those stated on the This electric household appliance ground. Rating plate located on the stainless should be connected to the water The pipe should not be immersed steel inner door of the appliance mains using the cold water supply in water. And that the electrical system to hose provided with the appliance which the dishwasher is connected only. [. . . ] The food particles are removed from the wash water, allowing it to be recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the larger food particles trapped inside the cup “C” and the semi-circular filter A after each wash; pull the cup handle upwards to remove them. The entire filter assembly should be cleaned thoroughly once a month: cup C + semi-circular filter A + cylindrical filter B. Cleaning and special maintenance Reassemble the filter parts (as shown in the figure) and reinsert the whole assembly into the dishwasher. [. . . ]