User manual BEKO DVG593

[. . . ] Before this appliance is removed for service or discarded, remove the door to the drying compartment. Do not install or store this appliance where it will be exposed to the weather. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these operating instructions. Repairs to electrical appliances should only be performed by qualified personnel. [. . . ] ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs). ^ Press and release the "Start/Stop T" button to start the new program. Adding or removing laundry during a program ^ Turn off the dryer using the "On/Off" button. ^ Open the door. , CAUTION - Do not touch the rear of the drum while adding or removing items!^ Turn the dryer back on with the "On/Off" button. 12 Child lock Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. ^ Wipe clean with a soft cloth. 15 Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. Should the container be full when the tumble dryer is started, or if it becomes full during normal operation: ­ The "Container" indicator will light. ^ Pull out the container slightly to the right with both hands. ^ Hold the cap open while emptying the container. ^ When the container is empty, push it back into its opening until it clicks into place. Do not drink the condensed water! 16 Dryer care Cleaning the condenser Removing the condenser ^ Open the door. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Detergent residues, hair and lint in the drying air can penetrate filters and clog the condenser. Particles from the cool air sucked in from the install location can cause blockages. Items may shrink. More Dry Normal Less Dry Hand Iron Rotary Iron If items are still damp, dry again using "More Dry". If fabrics are too damp, dry again using "Less Dry". For items to be ironed with a rotary iron. For items which require ironing. To prevent moisture loss, roll up the laundry until ready to iron. Wrinkle-free Available drying options Turbo, Gentle, Anti-crease More Dry Normal Less Dry Reduce load size for fabrics that wrinkle easily. Special Programs Available drying options: Anti-crease only available in Fluff, Sturdy Woolens Delicate items which allow machine drying. Take items out immediately after the end of the program while still slightly damp. Allow items to air dry. Smooth Sturdy Fluff - TIMED CYCLES 20 min 30 min Available drying options Gentle, Anti-crease - Frequently asked questions What if the dryer will not run?Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. Fix See "Changing the light bulb. " Fix Make sure the dryer is on. Close the door properly. What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started?See "Child Lock. " What if the program stops, the "Anti-crease/End" indicator lights and the buzzer sounds?Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. Frequently asked questions What if the "Filter/Vent" fault indicator is lit?Open a window or door to increase airflow. What if the program runs too long or stops?Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in Select a higher spin speed in the wash the washer. [. . . ] ^ Use the front dryer feet and the rear excess end to transport the dryer from the packaging base to the installation site. , When the machine lid needs to be removed to reduce the height of the machine, a built under spacer kit* is necessary. The cover plate of the built under kit replaces the appliance lid and ensures electrical safety. The electrical connection should be near the dryer and accessible at all times. Extended machine feet* are recommended at a built-in height of more that 33 1/16" (840 mm). [. . . ]