User manual BEKO CWB 9831 ANP

[. . . ] Remember that this user manual is also applicable for several other models. explanation of symbols Throughout this user manual the following symbols are used: c Important information or useful hints about usage. Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. [. . . ] In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. "CAUTION: Accessible parts may become hot when used with cooking appliances. Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period (Fire hazard). Light, Suction Unit, Filters, Lower Duct 7 1 PVC Pipe (fitted) 8 1 Inclinable grid (fitted) 9 1 Reduction flange ø 150-120 mm 10 1 Metal cover Width Depth Height Supply voltage Control Suction power Motor power Lamp power Fuse Air outlet pipe diameter Net weight Gross weight Color Markings on the product or the values stated in other documents supplied with the product are values obtained under laboratory conditions as per relevant standards. These values may vary according to the usage of the product and ambient conditions. If you want to use the hood in suction version with the air outlet at the back of the hood, make sure to follow the indications given below in the drawing for a correct boring operation of the air outlet opening. When installing the hood in recycling version it has to be taken into consideration that space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm. on the wall , trace: · A vertical line up to the ceiling or top limit, at The centre of the area where you intend to fit the hood; · As shown, mark a reference point at 847 mm above the horizontal reference line, and at X mm (X= see table in figure) to the right of the vertical reference line. Drill the points marked using a ø 12 mm bit · Insert plugs with screws and brackets 11a in the holes then tighten them. As shown, mark a reference point at 53 mm above the horizontal reference line, at the center of the of the vertical reference line. From inside the hood canopy, adjust the screws Vr to set the Hood Canopy level. When installing the hood in ducting version, basing on the installer's choice, a rigid or a flexible pipe with a ø 150 or 120 mm is used in order to connect the hood to the air outlet piping. The pipe connection can be made on the upper part or on the rear side of the hood. [. . . ] Led Leds off Leds C-D-E-F light up according to the speed that is set Lights up when speed 1 is active Lights up when speed 2 is active Lights up when speed 3 is active Lights up when Intensive speed is active Leds C-D-E-F light up according to the speed that is set Turns the lights ON/OFF at maxi- Led H lights up Press and hold the button for 2 Seconds to turn the lights on at in- The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. When refitting the filters, make sure that the handle is visible on the outside. These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage. [. . . ]