User manual BEGLEC FX 1000 V1.1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BEGLEC FX 1000. We hope that this BEGLEC FX 1000 user guide will be useful to you.


BEGLEC FX 1000 V1.1: Download the complete user guide (2488 Ko)

Manual abstract: user guide BEGLEC FX 1000V1.1

Detailed instructions for use are in the User's Guide.

[. . . ] The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages. [. . . ] The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance. The minimum distance between fogger output and objects must be more than 1 meter. NEVER hold your hands close to the fogger output, the fog is very hot and can cause serious burnings !To protect the environment, please try to recycle the packing material as much as possible. Make sure that nobody can put their hands just in front of the output. plug the supplied remote in the "remote control" input (2) on the back of the unit. Don't insert or remove the remote while the fogger is connected to the mains!Make sure to plug the fogger in a mains wall socket with earth connection Switch the fogger on and wait for about 8 minutes. (warm up time) IMPORTANT: Please note that the fogger is ready when the green LED on top of the "manual fogging" button (n°3 on the remote) is on. REMOTE CABLE: connect the special 5pin connector (1) to the remote input on the back of the fogger. DMX OUTPUT: 3-pin female connector, used to connect the fogger with the next unit in the DMX chain. DMX INPUT: 3-pin male connector, used to connect the fogger directly to a DMX-controller or another unit in the DMX chain. INTERVAL KNOB: while the fogger is in timer mode, this knob is used to set the time it takes (interval) between 2 bursts of fog (range = 9s ~ 275s) 6. DURATION KNOB: while the fogger is in timer mode, this knob is used to set how long the fogger will produce fog (range = 0, 5s ~ 10s) 7. MANUAL FOGGING BUTTON: for as long as the green LED is on, you can press this button at any time to produce fog. (regardless of the operation mode selected with the timer on/off button [8]) 8. TIMER ON/OFF BUTTON: used to switch the timer function on/off: LED is green: timer function is activated, use the interval + duration knobs. LED is off: timer is switched off, the fogger can be used in DMX or manual mode. ON/OFF BUTTON: used to switch the controller on/off: LED is on: the controller can be used. (until it needs to warm up again) Some extra information: Manual operation: switch the timer off (button "8") Timer operation: switch the timer function on (button "8") DMX operation: switch the timer off (button "8"), see the next chapter to learn how to install and setup the fogger for DMX operation. Hint: you can press the "manual fogging" button (7) at any time to produce some extra fog if needed. Used with the optional wireless RC-1 controller: Connect the special 5pin connector (1) to the remote input on the back of the fogger: the red LED (3) turns on. [. . . ] The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. Cleaning the fogger: To prevent obstructions in the heater, pump and tubes, the fogger should be cleaned on a regular basis: every 100h of continuous operation is a good reference. Switch the fogger off Remove the nozzle (metal part where the fog leaves the fogger) Remove the fog liquid from the tank Fill the tank with about 1liter of a solution containing 80% distilled water and 20% white vinegar. Switch the fogger on and wait for about 8minutes (warm up time) Put the fogger in continuous operation mode until the tank is empty Put the nozzle back in place Remove the eventual residues of the cleaning solution and refill the tank with fog liquid. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC FX 1000




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC FX 1000 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.