User manual BEGLEC DSP-12 V1.2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BEGLEC DSP-12. We hope that this BEGLEC DSP-12 user guide will be useful to you.
Manual abstract: user guide BEGLEC DSP-12V1.2
Detailed instructions for use are in the User's Guide.
[. . . ] ⷠWhen installed in a booth or flight case, please make sure to have good ventilation to improve heat evacuation of the unit. ⷠTo avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance. ⷠChoose the place where you put your installation very carefully. [. . . ] This unit may only be installed by qualified personal, following the rules for electrical installations in your country!After installation always put the metal covers back in place and make sure to use proper cable entry glands (see picture) to protect the wires from unwanted traction and friction. Since you have only 1 phase wire (L) you must make bridges between the L1/L2/L3 inputs and connect the phase wire to these inputs. Please refer to the overview below to fully understand the menu structure of the DSP12: Since you have 3 phase wires you can connect these directly to the corresponding L1/L2/L3 inputs. You can clearly see which buttons to push to select a certain function. In most cases the DSP12 is in normal working condition (display shows channel output condition). With the "up/down" buttons you can scroll through the 6 available menus. After +/-30sec the DSP12 returns automatically to the normal working mode. This means that you can only use the analog inputs when no DMX-signal is detected. When the DMX-signal is not present you have 3 options: · Hold: In case of DMX-fail the DSP12 keeps the last scene on the outputs. ⷠPress "menu" and "up/down" until the display shows "Dmx fail". Press "up/down" until the display shows "Hold" · Press "esc" to store this option and leave the menu. Press "menu" and "up/down" until the display shows "Dmx fail". Press "up/down" until the display shows "Analog" · Press "esc" to store this option and leave the menu. Press "menu" and "up/down" until the display shows "Dmx fail". Press "up/down" until the display shows the desired program (Prog 01 . With the DSP12 you can select a different working mode (curve) for each individual channel. This is a nice feature if you need to switch light effects on/off while at the same time you have to dim lamps. This is a good option if you just need a certain output level on each channel over a long time (shops, exhibition booths, pubs etc. You can set a certain level for all channels at once or for each individual channel. Press "menu" and "up/down" until the display shows "Preset". Press "up/down" until the display shows "All" · Press "esc" to store the selected level and leave the menu. [. . . ] Press "up/down" to set the desired preheat levels and channel numbers until all channels are set. On the DSP12 you can set the DMX start address for the complete unit or for each channel separately. Setting the start address for the complete unit: · Press "menu" and "up/down" until the display shows "Dmx addr" · Press "up/down" until the display shows "Block" · Press "esc" to store the selected level and leave the menu. Press "menu" and "up/down" until the display shows "Dmx addr" · Press "up/down" until the display shows "Single" · Press "menu" to select this option: the display shows the channel number on the first row and the DMX address on the second row. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC DSP-12
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC DSP-12 will begin.