User manual BEGLEC BT-36L1 V1.0
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BEGLEC BT-36L1. We hope that this BEGLEC BT-36L1 user guide will be useful to you.
Manual abstract: user guide BEGLEC BT-36L1V1.0
Detailed instructions for use are in the User's Guide.
[. . . ] The minimum distance between light-output and the illuminated surface must be more than 1 meters To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages. [. . . ] Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable (number 3 on the picture) that can hold 12 times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is used in standalone or master/slave mode. SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or master/slave mode. To select any of the pre-set functions, press the MENU button up to when the required one is shown on the display. After 8 seconds the display will automatically return to the main functions without any change. Once the correct address shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Once the mode is selected, press the ENTER button to setup (Or automatically return to the main functions without any change after 8 seconds. ) To go back to the functions without any change press the MENU button again. Tilt movement angle: 90° (60° above horizon; 30° below horizon. Tilt movement angle: 90° (vertically, front 75°; back 15°) Slave Mode Used to make the slave unit work in opposite to the master or to work in complete sync. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Sound Mode The unit works to rhythm of the beat when used in standalone or master/slave mode Press the MENU button until is shown on the display. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Blackout Mode Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMXsignal. No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone mode. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. [. . . ] The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. Every information is subject to change without prior notice You can download the latest version of this user manual on our website: www. Ce symbole représente la distance de recul minimum à respecter, c'est-à-dire, la distance minimum entre le projecteur et la surface à éclairer. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC BT-36L1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC BT-36L1 will begin.