User manual BEGLEC ATLAS VERSION 1.1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BEGLEC ATLAS. We hope that this BEGLEC ATLAS user guide will be useful to you.
You may also download the following manuals related to this product:
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
BEGLEC ATLAS VERSION 1.2 (2511 ko)
BEGLEC ATLAS VERSION 2.0 (2218 ko)
Manual abstract: user guide BEGLEC ATLASVERSION 1.1
Detailed instructions for use are in the User's Guide.
[. . . ] This symbol means: indoor use only This symbol means: Read instructions To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages. [. . . ] Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. This input receives instructions from a DMX-controller or from another unit when used in master/slave mode. DMX output: 3pin female XLR-connector used to connect the Atlas with the next unit in the DMX chain or with another Atlas when used in master/slave mode. Hanging bracket with 1 knob to fasten the unit and a mounting hole to fix a mounting hook. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. How to set the DIP-switches to obtain the right starting address: Each of the first 9 DIP-switches correspond to a certain DMX-value: DIP #1 #2 #3 #4 #5 #6 #7 #8 #9 Value 1 2 4 8 16 32 64 128 256 Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. You can combine the values of these switches to become any starting address between 1 and 512: Begin address = 01 switch 1=ON values: 1 Begin address = 05 switch 1+3=ON values: 1+4 = 5 Begin address = 09 switch 1+4=ON values: 1+8 = 9 Begin address = 13 switch 1+3+4=ON values: 1+4+8 = 13 . [. . . ] During inspection the following points should be checked: All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded. Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation. When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC ATLAS
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC ATLAS will begin.