User manual BEGLEC AKI COLOR DMX512

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BEGLEC AKI COLOR DMX512. We hope that this BEGLEC AKI COLOR DMX512 user guide will be useful to you.


BEGLEC AKI COLOR DMX512 : Download the complete user guide (666 Ko)

Manual abstract: user guide BEGLEC AKI COLOR DMX512

Detailed instructions for use are in the User's Guide.

[. . . ] Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit. It's important to ground the yellow/green conductor to earth in order to avoid electric EC Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002; EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996, EN61000-4-11: 1994. & Harmonized Standard EN60598-1: 2000+ALL:2000+A12:2002 Safety of household and similar electrical appliances Part 1 : General requirements 3D shock. [. . . ] Troubleshooting Following are a few common problems that may occur during operation. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one. Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit. The stepper motor might be damaged or the cable connected to the PCB is broken. Check and if necessary replace the lamp on the head. - 5. 5 DMX512 Connection The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 3. How To Install The Unit 3. 1 Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation. If you use a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. Connect the unit together in a "daisy chain" by XLR plug from the output of the unit to the input of the next unit. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. If one fixture in the chain is not working all the fixtures after that point will continue to work normally because the DMX signal will always pass through each fixture. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The end of the DMX512 system should be terminated to reduce signal errors. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5D AK-250 AK-150 3. 2 How To Install The Unit On The Floor 1. Refer to the unit's foot bracket hole pattern (B) to set the bolts (C) into the floor and screw the unit. Conjunction the unit's power supply cord to the mains power supply (D). Be sure that the local power outlet match that of the required voltage for your unit. [. . . ] Use "-" and "+" button to change the DMX512 address. Once the address has been selected, press the ENTER button to setup the DMX address. To go back to the functions without any change press the MENU button again. Focus Adjust Press the MENU button up to when the is blinking on the display. Pressing ENTER button, the unit will focus on different color each time you press ENTER button. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BEGLEC AKI COLOR DMX512




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BEGLEC AKI COLOR DMX512 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.