User manual B-52 MATRIX 200

[. . . ] INSIDE THIS INSTRUCTION MANUAL Important Safety Instructions / Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Features / Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Amplifier and Mixer Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Set-up & Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Read these instructions. Follow all instructions Keep these instructions Heed all warnings Do not use the MATRIX-200 near water. Be extra cautious when moving the system during rain or while transporting the system over wet surfaces as water might splash on to the amplifier. To reduce the risk of fire or electric shock, do not expose the system to rain or moisture. [. . . ] RING must be connected to the input of external processor, and TIP must be connected to the output of external processor. Please refer to the diagram labeled "Y-Cable Setup" on Page 7 of this manual for a graphic depiction of this. NOTE: Different processors may have a different configuration than the MATRIX-200 on their connectors. Please review the instruction manual information of the external processor before assuming it is the same as the MATRIX-200. If the external processor uses a different connection standard, then you will likely need to buy adaptors to properly connect the two units together. FOOTSWITCH EFFECTS/MUTE: This 1/4" jack is used to connect footswitch to remotely mute digital effects and master volume. RECORD OUTPUTS: RCA jacks to connect stereo recording device to MATRIX-200. PLAYBACK INPUTS: RCA jacks used to connect stereo source to MATRIX-200. This input bypasses all controls, including Master Volume (9) and Equalizer (1), (2), and (3), and is controlled only by playback level control (4). It is also not affected by Mute Footswitch (22). INPUT SECTION The Input section of the MATRIX-200 controls various aspects of the external audio sources which can be plugged into the mixer, including microphones, guitars, keyboards and certain other devices equipped with either 1/4" jacks, 3. 5mm stereo jacks, or microphone outputs 10. INPUT - EFFECTS: Controls level of each individual channel routed to digital effects section when Effects Master/Input switch is in Source position. This improves performance of the system by causing a more ideal acoustical summation of the subwoofer and main speakers. It does so by limiting cone excursion, and by increasing the headroom available to both the speakers and amplifier. HEADPHONES: 1/4" stereo jack used to connect headphones for monitoring when speaker use is not possible, or if headphones are preferable. NOTE: This jack is inactive if the speaker cables are inserted into the speaker output jacks (1). VOLTAGE SELECTOR SWITCH: DO NOT CHANGE THIS SETTING WITH THE AC MAINS POWER ATTACHED!This switch is only used to modify the unit when it is transported to a different location with a different available AC mains source (such as moving a unit bought in the USA to Europe). Please check that this switch is in the appropriate position for your local electric source. WARNING: Using an improper setting on this switch can destroy the MATRIX-200, create an electrical hazard and void your warranty!Do not change this setting unless you must to match to the AC mains power available. AC INLET: Male IEC AC mains connector for standard detachable AC mains cords. This cord will also need to change if the unit is moved between regions with different AC mains voltages. [. . . ] FOR YOUR PROTECTION: Please complete and mail the Purchase Information Card within (10) ten days of the date of purchase so that we may contact you directly in the event a safety notification issued in accordance with the 1972 Consumer Product Safety Act. In addition, we ask that you complete the brief questionnaire so me may analyze your answers and in this way, help us evaluate our customer needs. CUSTOMER SERVICE: Our dedicated staff is ready to help you with any B-52 warrant or product questions you may have. Please call 323-277-4100 (9:00AM to 4:00PM Pacific Standard Time). Limited Warranty Thank you for choosing a B-52 sound product. [. . . ]