User manual AVIOSYS IP POWER 9258WIFI V1.1

[. . . ] IP Power 9258 WiFi User Manual Firmware Version: 1. 1 Date Released: 10/08/2009 -1- Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Power 9258 WiFi was designed for indoor use, we carry no responsibility for possible damages caused by outdoor use, especially in the rain. Please use the power adapter provided by the dealer, we carry no responsibility for the possible damage from using power adapters not . Please contact the dealer If IP Power 9258 WiFi is not working properly. Copyright © 2009 All rights reserved. [. . . ] TYPEU/C GFE 10A 250V (PF) -9- 4. ) Hardware Setup 1. ) Connect the IP Power 9258 WiFi to a HUB or Router with a RJ45 network cable. This will 1. ) Click on the REF button in IPEdit, detect the network settings and setup the device automatically. 2. ) Once settings have been detected hit the apply button to apply the new settings. - 13 - 3. ) Hit yes to confirm and Enter the login and password for the Device to Approve changes Default Login: admin Password: <blank> 4. ) Give the device 1 minute then hit the rescan button on IPEdit to confirm the changes have been made. b. Custom Setup (Advance Users) 1. ) Highlight the device on the local devices section and on the right side of IPEdit all network information on the device will be displayed. - 14 - If the device is not on the same network a Red Exclamation mark in the IP Network information section will appear 2. ) To setup the device, type in the correct Gateway and IP Address. The gateway address: Gateway Address: The gateway address can be obtained in Windows under the network connections page IP Address: Make sure the first 3 sections of the IP Address matches the gateway address. Example: Gateway Address ­ 192. 168. 1. 1 IP Address ­ 192. 168. 1. xxx 3. ) Once the Default Gateway information has been obtained, enter the correct information into IPEdit and hit the submit button. - 15 - 4. ) Then hit the rescan button on IPEdit to confirm the changes have been made IP Service How to use IP Service on IPEdit: IP service allows the user to directly connect to his / her device through the internet without having to remember long confusing IP Address. Instead with this IP Service Technology, the user only has to remember the name of the device that the user has selected. Then the user can connect to IP Service, type in the device name, and connect directly to the device. First if you have de-activated IP Service on your device make sure you re-enable it. (Refer to your manual if you have questions on How to activate IP Service) 1. ) Open IPEdit, the device will show up in the Local Device Section. If you have not selected a name for the device, please refer to the section on the manual labeled: "Naming your device". 2. ) To start IP Service, Hit the green connect button on the top of IPEdit. 3. ) Once you have been connected search for your device by typing in at least the first 3 letters that you named your device with. 4. ) Double click on your device and a Internet Explorer window will appear connecting directly to your device. *Remember: It is crucial to have the IP Address of the device port forwarded from the router that you are using so you can connect to your device from anywhere. Please refer to your routers user manual on how to port forward your device. - 16 - 6. ) Hardware Interface Reset To Reset the device back to manufacturer default, use a small pen or pin and press the reset button firmly and hold for a minimum of 10 seconds. Once you hear a "beep" sound the device will be reset. Restart To Restart the device, use a small pen or pin then press and release the restart button. The device will automatically restart. How to Replace Fuse 1. ) The fuse is located between the power switch and the power input plugs. 2. ) Carefully remove the fuse holder with a flat screwdriver. 3. ) The fuse can be purchased at most electrical stores Model: U/C GFE 10A 250V (PF) - 17 - 7. ) Web Interface Connection to your Device Once the 9258 WiFi has been setup correctly, log into the device. First Option 1. ) Go to IPEdit find the device that is being used 2. ) Double click on the device link and a IE window will appear with the loading screen Second Option 1. ) Open Internet Explorer type in the IP Address of the device followed by the : sign. For example: http:192. 168. 122. 188:9258 192. 168. 122. 188 ­ IP Address 9268 ­ Port 2. ) Once you have typed in the address the 9258HP is ready to use. The default password for the 9258 WiFi Login: admin Password: <blank> The Control Console The Right Panel of the Web Interface controls the functionality and setup of the IP Power 9258 WiFi. - 18 - The IP Power 9258 Wifi Console consists of four main sections which will be explained in details below. Power Control Settings: Power Controls Scheduler Ping System Configuration: User Management Change Password Network Settings Wireless Settings PPPOE Settings Date & Time Advance Settings Maintenance DDNS IP Server & CNT E-mail Settings Black List Information System Log Http Commands XML Information Power Control Settings The Power Configuration Section allows you to directly control the outlets of the 9258 WiFi as well as schedule daily, weekly, and monthly power cycles. - 19 - Power Controls The Power Controls page allows you to control the power Power Control Power No: This section shows the outlet of the output that you would like to control Name: If the output has been named the name that you have chosen will show up here Controls: The control section will allow you to turn on or turn off the outlet Timer: The timer allows you to Alarm: The alarm section allows the 9258 WiFi to notify you when an outlet has been turned on or off. There are two ways that you can be notified either by E-mail or by a beeping sound. Status: The status function will show you whether the power is on or off. System Startup Power Default Value The system Power Default Value allows you to set the power ports on on or off when the device has been turned on. For example if you would the 9258 WiFi to have the power ports on on you can Power Control Rename Changing the Name of your Device - 20 - Device Name: Allows you to name the 9258 Wifi device. [. . . ] Email will E-mail the current log page to the selected receiver mail in the E-mail Http Command The Http Command section is a very powerful tool in the 9258 WiFi. This section allows you to easily create HTTP Commands to specific commands you are looking for. It also allows you to run commands directly from here. Command: The command is the command name Parameter: Is the parameters that you would like to be used or ran in the command. Auth Req. : If a password is required Allowed User: Which user is allowed to use this command Action: a. ) Run CMD: Will execute the command you have desired b. ) Cmd Syntax: Will produce the syntax needed to execute the command manually. [. . . ]