User manual AVIOSYS IP KAMERA 9076FXD V1.2.1.6

[. . . ] IP Kamera 9076FXD User Manual Release Date: 10/12/2010 Manual Version: V1. 2. 1. 6 - 1Ref#9076101012 Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. It is the responsibility of the user for any possible damages caused by outdoor use, especially in the rain. Please use the power adapter provided by the dealer, the manufacturer responsibility for the possible damage from using power adapters not. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of us. [. . . ] Intranet (LAN): When using the IP Kamera from within the network this is the best option. Custom: This setting allows you to manually input a setting for the Bit Rate, FPS, and picture quality. M-JPEG Settings: The available Quality settings and FPS for the M-JPEG settings are shown below - 27Ref#9076101012 M-JPEG Quality Settings High Medium Low M-JPEG Frame Rate Settings 30 FPS 15 FPS 7. 5 FPS 3 FPS 1 FPS MPEG4-2 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 15fps or 7. 5fps MPEG4-1 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 30fps, 15fps, or 7. 5fps Note: PTZ is only available in the mode below. When you enable PTZ it will automatically jump into that mode. - 28Ref#9076101012 Tune Image The tune image settings section allows you to control and tune the picture quality of the image. Keep in mind, the quality of the picture will also be affected by the quality of the lens that is being used. White Balance: Select from the following options auto, indoor, or outdoor Day and Night: Select the mode Day or Night TV Output: Select the mode enable or disable to output to a T. V Binning / Skipping mode: Binning enables low light-light performance. Select Binning, Skipping, 4x Binning mode (default is Binning) BLC (Backlight control): Select from one of the options on or off to control the Backlight: Select a value between (0~100%) Brightness: Select a value between (0~100%) Contrast: Select a value between (0~100%) Saturation: Select a value between (0~100%) Sharpness: Select a value between (0~100%) Default: To Return all values to normal default click on this button. Note: Make sure you click on the Apply button to save any changes made - 29Ref#9076101012 Network Network The network section allows you to setup the network information for the IP Kamera 9076. If this is enabled the IP Address of the device will be automatically provided by the router of the device. IP Address: Actual IP Address of the device can be found here LAN IP Address: Local Area Network Address. Subnet Mask: Subnet Mask information Default Gateway: Default Gateway Address DNS Server: Domain Name System Address Http Port: Enter the port that you would like MAC: The Mac Address or physical address of the device Note: Make sure you click on the Apply button to save any changes made - 30Ref#9076101012 FTP The FTP section of the IP Kamera 9076 allows you to save video clips FTP Server: The FTP server address is where the IP Address of the FTP server will be entered. User Name: Enter the FTP Username Password: Enter the FTP Password File Upload Path: Enter the upload path of the FTP Server File Upload Path: Enter the upload path of the FTP Server SMTP (Outgoing E-mail Server) Enter the SMTP E-mail server information here. The SMTP section allows the 9076CSWO to send emails out using the SMTP settings. My Server Requires Authentication: Some servers require SMTP Authentication for security purposes. If your email server requires this option, make sure to have this section checked. Account Name: Enter then login of the mail account Password: Enter the password of the E-mail account Use SSL Connect: If the email server requires SSL (Secure Sockets Layer) this option need Sender Email: Enter the Sender Email Address SMTP Server: Enter the SMTP Outgoing mail address - 31Ref#9076101012 Email Address: Enter the Receiving Email address Submit: After all settings have been made. Send Test E-Mail: This button will send a test e-mail to the designated account. Note: If you are having problems sending emails out and the settings are correct. Please check your DNS Server address to make sure you can send email out. SNTP The SNTP is a protocol for synchronizing the clocks of computer systems. SNTP Server: Enter the SNTP server address. Europe -- europe. pool. ntp. org Asia -- asia. pool. ntp. org Oceania -- oceania. pool. ntp. org North America -- north-america. pool. ntp. org South America -- south-america. pool. ntp. org Africa -- africa. pool. ntp. org Time Zone: Enter the corresponding time zone Automatically adjust for daylight saving time: Check this section if you want daylight saving time to be implemented automatically. - 32Ref#9076101012 IP Service IP service is a added service that provides you a platform so you do not remember a long IP Address. Just enter the name of your device into IP Service and you can find your device. Note: Port forwarding will be required on your router to connect to the device In this section you can to turn off/on this service as well as select which server you would like your device on. [. . . ] Left Click: Will zoom into the picture Right Click: Will zoom out of the picture Left Double Click: Will zoom to the largest possible zoom Right Double Click: Will zoom to the smallest possible zoom. See below how zoom might be used: Enlarging Pop Windows With Pop surf the user can enlarge the screen of the video stream. Basically all you need to do is to put the mouse cursor on the bottom or edge of the video screen then left click and drag. Please see the picture below for more details: Message board The message board section allows users to interact with other users easily on surf pop. [. . . ]