User manual AVIOSYS IP KAMERA 9070CS-POE V1.3

[. . . ] IP Kamera 9070CS-PoE User Manual Release Date: 10/20/2009 Manual Version: 1. 3 - 1Ref#90020326K0709 Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070-CS was designed for indoor use, the manufacturer responsibility for possible damages caused by outdoor use, especially in the rain. Please use the power adapter provided by the dealer, the manufacturer responsibility for the possible damage from using power adapters not . Please contact the dealer If IP Kamera 9070-CS is not working properly. [. . . ] Then the user can connect to IP Service, type in the device name, and connect directly to the device. Note: The IP Kamera9070-CS PoE requires you to select Server 2 on IP Service 1. ) Open IPEdit, the device will show up in the Local Device Section. If you have not selected a name for the device, please refer to the section on the manual labeled: "Naming your device". 2. ) To start IP Service, Hit the green connect button on the top of IPEdit. 3. ) Once you have been connected search for your device by typing in at least the first 3 letters that you named your device with. Then hit the search button. 4. ) Double click on your device and an Internet Explorer window will appear connecting directly to your device. Note: It is crucial to have the IP Address of the device port forwarded from the router that you are using so you can connect to your device from anywhere. Please refer to your routers user manual on how to port forward your device. - 19Ref#90020326K0709 6. ) Web Interface Connecting to the 9070-CS Once the9070-CS PoE has been setup correctly and access your IP Kamera9070-CS PoE. An Internet Explorer browser screen pop up with the login screen. Default IP: 192. 168. 1. 168 (When 9070 is connected to PC directly) Default Login: Admin Default Password: 12345678 1. ) After you have logged into the device you will be required to install active x controls. If this screen does not appear make sure you allow active x. 2. ) Right click on yellow bar and install the activeX controls. - 20Ref#90020326K0709 3. ) Then click the install button and install the active controls. 4. ) Once activeX controls have been installed the video feed will show on the screen Note: If there is no active x controls that are showing up, please go to internet explorer and enable activeX controls. - 21Ref#90020326K0709 The Control Console Section of the webpage. In this The IP Kamera9070-CS PoE Control Console starts in the section navigate to the other options and settings of the9070-CS PoE Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows you to edit the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc. - 22Ref#90020326K0709 Network: The network section allows you to change the devices network settings, ftp settings, smtp (email) settings, sntp settings, and IP service settings. System: The system section allows you to change the devices date and time, set time stamp for video, users, audio settings, update, event log. Application: The application section allows you to change the video recording format, ftp storage settings, SD Card settings, EPTZ-Set: The EPTZ allows you to zoom into the cameras image using digital zoom with pan & tilt. Media Player: The Media player can directly access the files in the built in memory. Each video file & picture can be accessed here and streamed through the internet. Live Video The Live video section of the IP Kamera 9070 is where you will live view the video of the device. From here you can change resolution, record onto current pc, take a snapshot, zoom, and detect motion detection. Type and Zoom Type: The type function allows you to set the streaming format for the IP Kamera 9070. You can select from the following type of resolutions depending on the format type you have set in the image settings. M-JPEG (640x 352) MPEG4-1 (1280x720) MPEG4-2 (352x192) Zoom: The zoom function allows you to select the screen size of the stream. Depending on the type that you have selected there will be different zooms that will be available. 1X zoom: The 1X zoom is the normal view for each type. - 23Ref#90020326K0709 2X zoom: This 2X zoom is 2 times the normal view for that type. Scaled 720: Is a resolution only available in MPEG-4-1, which sets the picture at 720P. This function is very useful when trying to display on larger monitors. Motion Detection Motion Detection: The motion detection icon will display when motion has been detected. This setting must be activated in the application section When no motion is detected the motion detection icons will look like the following. But, in the case that motion is detected and recording has started, the icon will look will light up blue. Active Record Active Record: Active record will show up when the device is actively recording. Active recording functions like motion detection, scheduler, or an alarm will set off this automatic recording. When active recording is not activated it will look like the picture below When the active recording function is activated it will light up in red. Record Record: The record button on the9070-CS PoE when pressed will record the live video feed and save the video into the computer viewing. To record follow the following steps: 1. ) Click on the record button 2. ) Then select the folder that you would like to store the file. Then hit okay. - 24Ref#90020326K0709 3. ) Once the folder has been selected the device will start to record. To stop recording click on the red icon and it will return to the original state. Note: Remember you need VLC codec to play the video files that are recorded Snapshot Snapshot: The snapshot function, creates a easy way take pictures of the current view in the IP Kamera9070-CS PoE. To setup the snapshot destination folder: 1. ) Click on the Application link on the bottom menu 2. ) Then select Snapshot path 3. ) In here browse for the location where snapshot pictures will be stored. [. . . ] For 1280 x 720P (Mpeg4-1): Port forward to 554 If Port forwarding (Mpeg4-2): Port forward to 8554 1. ) Open VLC media Player 2. ) Click on Tools > Preference 3. ) On the bottom of the screen click the Reset preference button. 4. ) On the bottom left hand side of VLC select the all under the show settings area. 5. ) Then in the left panel select Input / Codecs > Demuxers > RTP/RTSPl and type in the RTSP user name and RTSP password. - 49Ref#90020326K0709 6. ) Check the Cache value. Note: If the video is not smooth, set the caching value from 150~1200. 7. ) Save the new settings 8. ) Then go back to the VLC media player and go to Media > Advance Open File 9. ) Next select the network tab and under the protocol select RTSP. 10. ) Type in the RTSP address of your device For Mpeg4 Stream1 : rtsp://<IP Address>/mpeg4 For Mpeg4 Stream2 : rtsp://<IP Address>:8554/mpeg4 Example: rtsp://122. 116. 137. 123/mpeg4 - 50Ref#90020326K0709 Hit the play button and wait a few seconds for the program to start streaming. - 51Ref#90020326K0709 9. ) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070 a very simple task. Using Surf 16 CH and multi device DVR monitoring software, you can easily view your 9070CS. [. . . ]