User manual ASUS ESC1000 G2

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. [. . . ] Hotplug support configurations for SATA are disallowed under this mode. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Set to [RAID Mode] when you want to create a RAID configuration from the SATA hard disk drives. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. configuration options: [Disabled] [Enabled] SATA6G_1 (Gray) Hot Plug [Disabled] Configuration options: [Disabled] [Enabled]. This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. The following two items appear only when you set the SATA Mode item to [IDE Mode]. Serial-ATA Controller 0 [Enabled] Allows you to enabled/disabled the Serial-ATA Controller 0. Configuration options: [Disabled] [Enabled] [Compatible] Serial-ATA Controller 1 [Enabled] Configuration options: [Disabled] [Enabled] Allows you to enabled/disabled the Serial-ATA Controller 1. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. 6 USBConfiguration UEFI BIOS Utility - Advanced Mode Exit The items in this menu allow you to change the USB-related features. DISABLE option will keep USB devices available only for UEFI applications. Legacy USB Support [Enabled] [Disabled] [Enabled] [Auto] The USB devices can be used only for the BIOS setup program. 0 Support [Enabled] [Disabled] [Enabled] Enables the support for USB 3. Enables the support for operating systems without an EHCI hand-off feature. The following two items appear only when you set the HD Audio Controller item to [Enabled]. Front Panel Type [HD] [HD] [AC97] [SPDIF] [HDMI] Allows you to set the front panel audio connector (AAFP) mode to legacy AC97 or highdefinition audio depending on the audio standard that the front panel audio module supports. [. . . ] Installing four SLI-ready graphics cards Insert the four graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. Align and firmly insert the 4-Way SLI bridge connector to the goldfingers on each graphics card. Connect four independent auxiliary power sources from the power supply to the four graphics cards separately. [. . . ]