User manual APPLIED ENERGY LV100
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual APPLIED ENERGY LV100. We hope that this APPLIED ENERGY LV100 user guide will be useful to you.
Manual abstract: user guide APPLIED ENERGY LV100
Detailed instructions for use are in the User's Guide.
[. . . ] Secure the upper sash in the closed position and fit stops just below the level of the fan, to prevent damaging it when the sash is raised. If installing in a panel which is between 9mm Wall mounted out of reach of bath or shower. Electricity, gas, water behind the switch location (in the wall or above the ceiling). Lay in the cable from the isolating switch to the transformer location. [. . . ] Preparing the fan for installation Remove the front cover by pressing the release catches located on the sides of the unit with a 3mm screwdriver, whilst pulling the front cover forward M Mount the fan in the hole If working above Ground Floor Level, appropriate safety precautions must be observed. If installing in a wall, ceiling or vent Mark the position of the back plate B 1. Hold the back plate so that the terminal block faces you in the left hand corner, and the lip points towards the hole. Mark on the wall/ceiling or vent shaft the positions of the three fixing holes in the back plate. Drill screw holes in these positions if necessary, and fit wall plugs if necessary. If installing in a ceiling or vent, push the larger diameter piece of the telescopic wall tube onto the ribbed gasket. Feed the mains cable through the cable entry hole in the backplate to the terminals D 4. If wiring from above, leave the cable free to be fitted into labyrinth. Insert the lip of the back plate into the wall duct/ceiling or vent shaft as before. Fasten the back plate to the wall/ceiling or vent shaft using appropriate fasteners. Peel the backing from the foam strip supplied and attach it around the outside of the lip on the back draught shutter. Holding open the top and bottom vanes, insert the lip into the wall duct. Making sure the back draught shutter is level, mark the positions of the two fixing holes in the top right hand and bottom left hand corners. Drill screw holes in these positions, and fit the remaining wall plugs. Holding open the top and bottom vanes, refit the back draught shutter and fasten it to the wall using the pointed end self-tapping screws. If installing in a window or panel Sealing the hole E If installing in a window or panel no more than 9mm thick, fit the white rubber gasket around the edge of the hole. if installing in a panel or sealed double glazing more than 9mm thick , a DXG Double Glazing kit is required. Holding open the top and bottom vanes, insert the back draught shutter 2 into the spacer 3 so that the fixing holes in the top right and bottom left hand corners match those on the spacer. Insert two of the flat ended self-tapping screws provided and fasten the back draught shutter to the spacer. Someone else must hold the back draught shutter and spacer in position outside, with the spacer against the glass. Make sure that the two raised fixing holes in the spacer are horizontal and are positioned within the hole. From inside, hold back plate so that the terminal block faces you in the top left hand and the lip points towards the hole. [. . . ] Do not immerse the fan in water or other liquids to clean any other parts of the fan. Mains supply cable through the appropriate knockouts into their respective compartments. Våra tekniker finns till hands enbart på kontorstid (enbart Storbritannien), men du kan faxa dina frågor till hjälplinjen när som helst på numret +44 (0) 8799 000530. Se till att strömmen är bruten till fläkten innan något rengöringsarbete påbörjas. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE APPLIED ENERGY LV100
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual APPLIED ENERGY LV100 will begin.