User manual APPLIED ENERGY IDH1-8 INSTALLATION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual APPLIED ENERGY IDH1-8. We hope that this APPLIED ENERGY IDH1-8 user guide will be useful to you.


APPLIED ENERGY IDH1-8 INSTALLATION: Download the complete user guide (200 Ko)

Manual abstract: user guide APPLIED ENERGY IDH1-8INSTALLATION

Detailed instructions for use are in the User's Guide.

[. . . ] Position of air intake: · As far as possible from and opposite to the main source of air replacement to ensure airflow across the room (e. g. · Not where ambient temperatures are likely to exceed 50ºC, or above a cooker hob or eye level grille. · If installing in a room containing a fuel burning device, it is the installer's responsibility to ensure that there is enough replacement air to prevent fumes being drawn down the flue when the fan is operating up to maximum extract. · Exhaust air must not be discharged into a flue used for exhausting fumes from appliances supplied with energy other than electric. [. . . ] Removing the cover Insert a screwdriver in one of the 4 openings in the slanting corners of the box. Turn the screwdriver so that the corner piece unlocks and loosens the cover. Removing the motor and impeller assembly Remove the motor and impeller assembly by using the 3 click connections fixed to the casing. Insert a screwdriver into one of the grooves and turn it until the section becomes free. When all 3 positions are loosened the motor plate can be removed from the casing. Reassembly Place the ventilator unit in the correct position and click the cover back in place. Wiring Instructions · This appliance is intended for connection to fixed wiring · Check that the electrical rating shown on the fan matches the mains supply. · WARNING: THIS APPLIANCE MUST BE EARTHED · All installations must be supervised by a qualified electrician. · Installations and wiring must conform to current IEE Regulations (UK), local or appropriate regulations (other countries). · A means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules 1. Switch off the mains electrical supply and remove all fuses before commencing wiring. Wire the fan as shown below Connect the cable from the isolating switch to the electrical supply wiring. · Emitter malfunction: Pick up the emitter and walk towards the receiver. · It the system works when holding the emitter in the hand but not when it is placed on the wall, this may indicate the presence of moist or metal in the wall. · If the system works at reduced distance, this indicates either that the emitter has been placed outside the emitter range or an interference problem. You should then place the emitter closer to the receiver or outside the reach of the interference. · The system does not work even after placing it closer to the receiver. You should then check the programming and/or the battery of the emitter (see above) Existing installation · Check the batteries of the emitter(s) · Check the operation of the connected receivers · Check for interference caused by changes in the system environment (metal cabinets, walls or furniture moved. . . . ) Restore the original condition. The system automatically switches on: This is only possible if a foreign emitter previously programmed in the receiver is operated within the receiver range. Reset the receiver and reprogram the relevant addresses (see Programming). The system automatically switches off: This situation may be similar to point a) or may be the result of transient power cuts. MOUNTING INSTRUCTIONS AND RECOMMENDATIONS · Never mount the emitters and/or receivers in a metal distribution box, housing or netting. · Wherever possible, avoid mounting the emitters and/or receivers in the immediate vicinity of large metal objects. · Never mount emitters and/or receivers on (or near) the ground. [. . . ] 6 Fit the control buttons (Fig F) B) Screwing: Mounting on a flush-mounting box on a structured base, e. g. 2 Centre the assembly and screw onto the wall using the screws and plugs provided (Fig. E). 3 Click the emitter unit into the cover plate with the battery pointing upwards (Fig. C). - screw down battery clamp. For use in: BE/NL/FR/DE/AT/ES/PT/CH/DK/LU/GR/SL/CZ/NO/GB Do's and dont's · Do read all the instruction leaflet before commencing installation · Do install each fan with a double pole isolating switch. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE APPLIED ENERGY IDH1-8




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual APPLIED ENERGY IDH1-8 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.