User manual ACR ELECTRONICS AIS INSTALLATION

[. . . ] Please read this first! Warning: Although ACR strives for accuracy in all its publications; this material may contain errors or omissions, and is subject to change without prior notice. ACR shall not be made liable for any specific, indirect, incidental or consequential damages as a result of its use. ACR components may only be used in safety of life devices or systems, with the express written approval of ACR, as the failure of such components could cause the failure of the ACR device or system. If these fail, it is reasonable to assume that the safety of the user or other persons may be endangered. Copying of this document, and giving it to others and the use or communication of the contents thereof, are forbidden without express authority. [. . . ] L 35 NOTE:If installations are not in compliance to this requirement we cannot guarantee operation nor accept a warranty issue. Antenna Layout The position of the VHF and GNSS ­ antennas must be added to the existing antenna layout of the vessel. 3. 11. 3 Power Supply The NAUTICAST must be supplied from the emergency power source. A further requirement is to connect AIS to the reserve power source of the GMDSS. See sample in 9. 1 (Samples for battery calculation) Following documents are needed for the installation approval of the classification Antenna Layout (arrangement) Battery Calculation Connection / Block ­ Diagram with locations Type Approval Certificate 36 Y1-03-0204 Rev. L 4 Starting the NAUTICASTTM Setting up your AIS Transponder for operation. NOTE: IMO REGULATIONS MANDATE THAT YOU ENTER THIS INFORMATION. After installing the antennas and hardware the following User, Voyage related and Ship Settings data needs to be entered. a) b) c) Enter MMSI Number - See paragraph 4. 1 on entering information. Voyage related Data ­ After initial entry of the Voyage related Data any changes in the information below should be edited accordingly. Enter Cargo Type Enter Draught Enter Destination Enter ETA Enter Navigation Status. Enter Ship Settings Data - After initial entry of the Ship Settings Data any changes in the information below should be edited accordingly. Enter Call Sign Enter Ships Name Enter Length of Ship Enter Beam of Ship Enter Internal GPS antenna Position Enter External GPS Antenna Position (If Applicable). Enter Ship Type Password ­ Service and User passwords see section 4. 4 d) e) 4. 1 Entering the MMSI and IMO Numbers: Select from the Main Menu "Service Configuration" Number 6. The default password from the factory is mentioned on your AIS display at the protection foil. Please see the appendix in your User Manual for additional password information. . Enter Service Password and use the up and down arrows on keypad to select "Change MMSI / IMO" than press M5 "Select" or "by pressing number 3 on the keypad. Continue to 4. 2 after reboot, if no IMO number is available use the value 0 (Zero). Y1-03-0204 Rev. L 37 N 1o19' E 0o13' |1>0. 01|2>1. 30|3>1. 80nm |---------------------------------| Menu -----| | | +- 1. Graphical Display Settings | Displ| ---------------------------------------NUM|Select->| | |<-Back Service Configuration Menu Example: N 1o21' E 0o14' |1>0. 01|2>1. 30|3>1. 80nm |---------------------------------| 6. | | -----| | Displ| ---------------------------------------NUM| Select->| | |<-Back Note: MMSI and IMO Data input are limited to 9 characters. N 1o21' E 0o14' |1> N/A|2>0. 00|3>0. 10nm ********** Change MMSI / IMO *********** MMSI :1193046 IMO No. :303174162 ---------------------------------------NUM| Save | | | Back 38 Y1-03-0204 Rev. L 4. 2 Entering Voyage Related Data: Select from the Main Menu "Voyage Settings" Menu is USER password protected. The default password from the factory is mentioned on your AIS display at the protection foil. Please see the appendix in your User Manual for additional password information. . [. . . ] 1. 3) ITU-R M. 825-3 ITU-R M1084-3 IEC 61993-2 (2001) IEC 61162-1 (2000), -2 (1998) IEC 60945 (1996) IEC 61108-1 (1996) Technical Specification for Vessel Tracking and Tracing Systems for Inland Waterways (Ed. 1. 01 dated 10. 10. 2007) Test Standard for Inland AIS, (Edition 1. 0 dated 31. 5. 2007) GPS Antenna ACR GPS Antenna (28dB Gain) 2637 Verlegte Kabellänge < 40m Installed Cable lenght <40m 2009-10 ACR Electronics Inc. , 5757 Ravenswood Road, Fort Lauderdale, Florida, 33312 USA ACR Electronics Europe GmbH Handelskai 388 / Top 632 A-1020 Vienna, Austria Vienna, 2009-09-16 Zertifikate der benannten Stelle: Certificates from the notified Body / Certificats des Organismes Notifiés Spezifizierte Standards: Specified Standard(s) / Standard(s) Spécifié(s) Zubehörtyp: Type of Accessory ACR Part Number: Einschränkungen / Hinweise Restrictions / Comments Dokumentennummer: Document number / Num. du document Hersteller: Manufacturer / Fabricant Anschrift EU-Vertretung: Address EU-Representative / Adresse du Représentant pour l'UE Ort, Datum: place, date / Lieu, Date Unterschrift: Signature / Signature Andreas Lesch Managing Director Diese Erklärung bescheinigt die Übereinstimmung mit den genannten Richtlinien, ist jedoch keine Zusicherung von Eigenschaften. Die Sicherheitshinweise der mitgelieferten Produktdokumentation sind zu beachten. [. . . ]